Generic selectors
Exact matches only
Search in title
Search in content

Answer supervision

Viewing 15 posts - 76 through 90 (of 103 total)
  • Author
    Posts
  • #20990 Reply
    Ahuramazda59
    Guest

    hi , how can I block my caller ID in other phone when I call them ?

    #20991 Reply
    Tassos,
    Guest

    I have a serious problem
    I want to configure a cisco 1760 fxs-fxo with panasonic pbx 500, like this:

    Analog phone-router cisco- PPP – router cisco- Panasonic pbx.

    The problem is when i call from pbx -the number of the phone port- i listen a tone and only after i can take the number of the Phone on fxs.How i can configure to call from pbx directly to analog phone on fxs.

    #20992 Reply
    Saul Bejarano
    Guest

    Tassos:
    Your problem is not answer supervision but cisco configuration, you have to configure the right dial-plan on your cisco gateway, basically set up the dial-peers correctly.

    #20993 Reply
    Elie
    Guest

    is the answer supervion problem also available in the new analogue and DX Digital when we enable the ProgTone?? as it was available in A800??

    Elie

    #20994 Reply
    Tassos
    Guest

    thanks,
    but the big new problem are in the disconect times or in the way that cisco “understand” the td-500 panasonic when the user from pbx put the phone down.So, When a user from pbx/fxo call the remote user at fxs,the remote user rings correctly.BUT if this user don’t pick-up and the local(fxo) close the phone the line-ringing remains -up.If anyone knows anything about Cisco vs Panasonic,please talk…
    thanks….

    #20995 Reply
    Tassos
    Guest

    Happy New Year guys.

    #20996 Reply
    Saul
    Guest

    I can take a look at your cisco configuration, please send me your show run.
    saul@procomm100.com

    #20997 Reply
    Tassos
    Guest

    Goodmorning from Greece.
    After 11 hours of hard test i found the finaly synthesis of timers(cptone\freq/caedence/dbm0/….).
    I’m really thanks the people who looks for me.
    StBy.

    #20998 Reply
    Shashank
    Guest

    hi

    Anyone can help to know how can i use CAC 24 T1 Channel Bank with CDMA or GSM ( FCT )

    Its an urgnet

    regards
    shashank

    #20999 Reply
    Saul
    Guest

    For CDMA you can use cell sockets, for GSM you can use a GSM channel bank like Valiant, Orion or some other european GSM channel bank, in case you want to use cell sockets please do not post your bad experience back 🙂 they work but is really not painless, it will hurt your asr when you have a cell socket not working.

    #21000 Reply
    VOIP Brett
    Guest

    I am configuring a cisco as5350 with an t1 carrier access cb.

    Configuration:
    mode cas
    framing sf
    clock source internal
    linecode ami
    ds0-group 0 timeslots 1-24 type fxo-loop-start

    Can someone tell me switch settings on the CAC Channelbank?

    #21001 Reply
    raul
    Guest

    Hi I´m from Guatemala and i have a Clarent Gateway 1200. I don´t have any information about the configuration of the software could any of you help me with some information or manual. Thanks.

    #21002 Reply
    Nobel
    Guest

    I need to block ID sending using cisco AS5300 or Quantum A800, I want to know i there is any configuration or software that could block the number from appearing on mobiles or landlines with caller ID devices, can anyone advise pls..Thanks..

    #21003 Reply
    To Raul about Clarent
    Guest

    There is no information that is available online about Clarent.

    The Clarent units do not work by themselves, only under the control of a master unit, called the comand center.
    If you only have a gateway, all what you have is a old PC with some DSP units and FXS or T1 interface.
    I have myself some gateways 100, a command center and a gatekeeper, all of them unused because you need to buy the licence to operate them.

    Good luck

    #21004 Reply
    Nobel
    Guest

    Would the cisco AS5300 operate with a CAC CB or would there be answer supervesion issues? Thanks for your swift and kind advise.

Viewing 15 posts - 76 through 90 (of 103 total)
Reply To: Answer supervision
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">