- This topic has 286 replies, 1 voice, and was last updated 14 years, 7 months ago by MikeM to Shayan.
15th June 2005 at 14:38 #23832SimoGuest
As I answered in your other question in an equally un-related topic thread, you can easily find this information on Quintum’s web site by reviewing the product specification sheets.
In short the ASM has 4 fxo and 4 fxs ports. The AXM starts with 8 FXO and 8 FXS ports.24th June 2005 at 12:26 #23833Eno OGuest
Please I need to access my Quintum but I don’t know the original password before accessing it. Please if you have any idea, kindly email it to me. email@example.com
Thank you very much6th July 2005 at 23:50 #23834MaxGuest
What equipment is needed to to provide calling cards service. Can this be done with a intergrated Cisco or Quintum unit.7th July 2005 at 16:14 #23835Teodor GeorgievGuest
Guys, do not buy the FXO-equipped second generation Quintums.
They are still unreliable.
Their disconnect supervision algorithm is crappy.
You will fall into a trouble.21st July 2005 at 17:01 #23836ZamanGuest
I need to learn Quintum A800 and AX800 configaration,Can any one help me? I cometment I will do something for him.23rd July 2005 at 15:33 #23837ngozi braideGuest
we have used the configuration you sent, using our own ip addresses, but what of the call signal IP address,
what IP address SHOULD IT BE, YOURS
OR OURS.26th July 2005 at 12:40 #23838DJEUYAGuest
please i need documentation to install and setup my quintum A40026th July 2005 at 20:07 #23839MikeMGuest
did you try looking at Quintums web site under the support area?26th July 2005 at 22:09 #23840Wilson BoyrieGuest
On http://WWW.quintum.com, on the bottom of the page, click on customer service, you will have all the manuals and information about the Quintum.28th July 2005 at 15:44 #23841ZamanGuest
I think i can help you with your problem… i will expalin to you on the configurations29th July 2005 at 18:19 #23842JackGuest
“Quintum good all you people here bad” don’t give specific information. If don’t want to give information in details don’t write here.Thank you.30th July 2005 at 05:26 #23843bertcamroyGuest
Hello Zaman i can help you explain configurations… email me at firstname.lastname@example.org maybe i can help you..
what is your problem Jack?….31st July 2005 at 00:21 #23844RustyGuest
The latest Cisco IP-to-IP Gateway does SIP H323 and transcoding. It works as a SIP & H323 proxy softswitch and runs on several standard Cisco routers 1850, 2651xm, 3845, and others. Heck you probably have one of these routers all ready in stock. If you have any questions email me email@example.com August 2005 at 07:47 #23845riyfatGuest
I have a Quintum Tenor A800 +8 pstn line.Is it possible to run
multiple dial plan on a single Ip?
I want 2 run 4 local call & 4 pstn call on a single Ip. Is there any way to do it ?
Plz send me some basic
_call routing commands
_Ip config command
_pstn port test command
Thanking you.8th August 2005 at 04:00 #23846SurendraGuest
can someone help me to configure quintum A800 with cisco gateway?