- This topic has 87 replies, 1 voice, and was last updated 3 years, 9 months ago by
Ayat.
-
AuthorPosts
-
Aman
Guestdear, how can we improve paging success rate in E/// BSC? what paging parameters should we check in BSC?
Bijoy
GuestAman
Kindly let me know the following parameters.
BSC/BTS Parameters
1.MFRMS
2.AGBLK
3.BCCHTYPE
4.T3212
5.ATT
6.MAXRET
7.CRH
8.RAEPPMSC/MSS Parameters
1.BTDM
2.GTDM
3.TDD
4.PAGNUMBERLA
5.PAGTIMEFRST1LA
6.PAGETIMEFRSTGLOB
7.PAGEREP1LA
8.PAGEREPGLOB
9.PAGTIMEREP1LA
10.PAGTIMEREPGLOBBr\\
Bijoysewashi
Guesthow about in nokia? what are the parameters involved?
Bijoy
GuestHi Sewashi
In Nokia
BTS Parameters
1.MFR
2.AG
3.MBCCH or MBCCHC
4.PER
5.ATT
6.RET
7.HYSLet me know if you need MSC/MSS parameters too
Br\\
Bijoysewashi
Guestthanks bijoy for the parameters. can i also have the msc parameters? tnx..
also i would like to ask, is sdcch congestion/blocking related to paging success rate? kindly explain.
Bijoy
GuestAs you wish
Here we go
MSC Parameters
1.Repaging_Interval
2.Number_of_Repaging_Attempts
3.PAGING Method
VLR Parameters
1.TMSI PAGE REPETITION IN MT CALL
2.LIMIT FOR SIMULTANEOUS SEARCHES
3.SEARCH RESPONSE WAITING TIME
4.TMSI PAGE REPETITION IN MT SMS
5.TMSI UsedYes,SDCCH Blocking may affect the Paging Success Rate
Br\\
Bijoysewashi
Guestthanks bijoy for the parameters.
but can you explain how it is related to sdcch blocking? im a little bit confused. is it rach that is being used as a reply to a paging message?
Bijoy
GuestOk
Let me try.
In response to paging,RACH(Channel request) will be sent by the MS to the BTS with the CM service Type.In response to RACH,BSC will ask to BTS to activate a channel(usually SDCCH).Now,if there is no usable/free SDCCH available,BTS will reply with Channel NACK/Immediate Assignment reject.Now,since call set-up indication is not being sent to the MSC,so no paging response.Hence,PSR goes down.Ameen
GuestHi Bijoy,
Thanks for the information, however just wanted to point out that in Paging Scenario, “CM Serv Request” is not sent. Instead, when SDCCH is established, MS sends “Paging Response” to the network.
CM Serv Request (4 types) are only in Mobile Originated scenarios.
Moreover, RACH contains only Cause Values (for whichever service required), where CM Serv Req message is a layer 3 message which is only sent when SDCCH is established.
Regards,
AmeenBijoy
GuestThanks Ameen for the slight correction.
But again,as you have written “in Paging Scenario, “CM Serv Request” is not sent” is not correct.You contradicted yourself in your post itselfBr\\
Bijoyvijay
GuestHow to improve psr in zte MSC & BSC?
kuljit
GuestAre these parameters are also has to seen in ericcson system to improve PSR
Preethi
GuestHi Bijoy,
In nokia BSC, can you pl provide explanation of the BTS parameters which will improve PSR alongiwith full for
Thanks.
Regds’ PreethiMuyiwa Adedayo
GuestHello all,
I am just coming into the forum.
i am an RF engineer with MTNN and hope to fully be part of the house shortest time.Bijoy
GuestHi Preethi.
Please see my post down below for the paging parameters.
Please go through NED for details.Do ask for any doubt.Br\\
Bijoy -
AuthorPosts