- This topic has 468 replies, 1 voice, and was last updated 2 months, 3 weeks ago by
.
-
AuthorPosts
-
20th March 2007 at 22:07 #39635
telecom
GuestHi Comox,
u need the Flash Crad “5 Volt Series 2 (iMCxxxFLSA)” and the Memory Capacity greater than 20 MB.
If u need one PCMCIA card then send me a message to:
Best regards,
Holger
21st April 2007 at 14:54 #39636balouch
GuestDear All,
Can anyone guide me that commercial supply not available and when site load shifted automatically on genset then it is sure that site will not experience outage. but i face this trouble in Huawei gsm that site load not shifted on batteries.let me know what is wrong with this and what is faulty.
28th April 2007 at 09:29 #39637Jerrys
GuestI’m a BSS Engineer in a GSM company. There was congestin on TCH and a high value of SDCDR(SDCCH Drop Rate) on one of our site configured 1/1/1. I then added one TRX on the first sector making the configuration 2/1/1. I noticed the congestion on TCH is resolved but the value of SDCDR remained as high as before.
What could be the cause of that problem? Will the add of an SDCCH channel to the second added TRX solve the issue?
Thanks,
30th April 2007 at 02:15 #39638Sanjeeb
GuestDear All
i want to know the cards (RRI,FIU,E1/T1) used in BTS in detail and also the difference in between them
30th April 2007 at 07:36 #39639Tomar
GuestHi Jerrys,
In easy way, if you have TCH congestion, than add TRX. Than you will have much more capacity. If you have SDCCH congestion, than add SDCCH channels (change channel configuration from Comb to NonCom) or add more than one NonComb timeslots. One Comb is 4 SDCCH channels and one NonComb is 8 SDCCH channels. But if you have SDCCH drop than you have probably problem with interference. Check Idle Band. And try to find better BCCH frequency.
BR Tomar2nd May 2007 at 21:44 #39640Sasan
GuestHi,
FXC E1/T1 Card: Transmission Unit when there is no MW solution.It can Provide 4xE1(4x2M). Usually used when we have BTS near the BSC or when we want to use HDSL modem. (E1=Europe Standard for 2M,T1=US and some other countries standard)
FXC RRI Card: Transmission Unit when MW solution is available. It to Flexbus. Each FlexBus can connect to seperate ODU(OutDoorUnit like FlexiHopper or MetroHopper). It can provide totaly 16xE1 and ability to work as a Single or HotStandBy(HSB).
FIU 19: Transmission unit when you want to diMultiplex your signal from MW to E1(PCM). It has diffrent configuration
2IDU+2ODU= High Protection
1IDU+2ODU= HSB Protection
Single = witout Protection8th May 2007 at 09:36 #39641syed saadat hassan
GuestHi, All
I am working on ZTE10-OB06 ZTE outdoor bts every thing is ok we have two sectors,Sec A and Sec C its a highway site.The problum is that one sector is working and one is not taking traffic MSC is having alarm on CDU but visually there is no alarm, second thing is thatone sector is only working in night time.Temperature at that site is upto45deg celcious and the capicity of the BTS is -45 to+55. Please any one tell me the problum. THANKS10th May 2007 at 07:32 #39642NISHANT CHOUDHARY
GuestHI,
HOW CAN I CONVERT 404F700001E39F
CELL ID IN DECIMAL FORM.WARM REGARDS
NISHANT10th May 2007 at 10:27 #39643Rajiv Gujral
GuestDear Nishant,
I think there is some probem with the CGI u have given in the Hexa decimal.
U have given CGI : 404F700001E39F.MCC – 404 -> 404
MNC – F -> 15
LAC – 700001 -> 7340033(in question)
Cell ID – E39F -> 58271.Range of the LAC & Cell ID in GSM is 0 – 65535.
Regards
18th May 2007 at 21:23 #39644shamim
Guestwhats the load current need rbs-2106i
6th June 2007 at 14:15 #39645ANN
GuestHow many subscribers can one TRX/TRE(in Huawei technologies) handle at the same time in GSM.
THANK YOU
6th June 2007 at 19:43 #39646Shudeshna Mostafa
GuestHi all, would u plz tell me abt ERRICSSON bts installation
6th June 2007 at 22:57 #39647Shadiq
GuestDoes anyone know if it is possible to add radios to a nokia ultrasite bts without configuring the HW manager accordingly?
8th June 2007 at 21:35 #39648patrick.fr
GuestShadiq – 6 Jun 2007
Which card?
alarm: “difference between BTS ans BSC …” appears if you have a mistake on HW.
So you must use HW configurator.
13th June 2007 at 21:38 #39649Shadiq
GuestThank You! Patrick
-
AuthorPosts
- The forum ‘Telecom Design’ is closed to new topics and replies.