- This topic has 152 replies, 1 voice, and was last updated 1 year ago by OYEWUMI ABIODUN JOHN.
18th August 2009 at 10:44 #41486sujeet kumarGuest
i want to know …
which type of command use in ericsson bsc/msc/bts…service alarm27th August 2009 at 12:45 #41487Anand ParmarGuest
What is the Exact Difference Between ErlangB & ErlangC?
What maximum number of EDAPs a PCU can handle?1st September 2009 at 10:59 #41488AbhiGuest
@Amit : Kindly check the cabling at the antenna end. There have been instances of wrong tagging at the BTS end whereas the connections at the antenna end is somewhat different. Do you have TMA installed in that site?? If so, check the TMA status.13th September 2009 at 11:10 #41489aliGuest
i want learnd abut RBS and worck in ofice plz help
br/ali15th September 2009 at 02:03 #41490Jonathan KisarGuest
Can anyobody explain to me about the configuration of RBS 2216?
Is it possible to configure those kind of RBS with 6 sectors 2 sites, means that we seperate the 3 sectors in one site and another 3 sectors for another sites?
Please help2nd October 2009 at 08:45 #41491brightGuest
what type of fault is this and how can it be cleared: RX EEPROM checksum Fault10th October 2009 at 04:24 #41492RiyasGuest
I hv also faced this same alarm fr a 2111 expanded cab. RX EEPROM check sum fault. After reloading the flashcard it ceased.14th October 2009 at 14:33 #41493BrightGuest
i need help on how to tackle RX Diversity faults from RBS 2206 because it clears and then it comes back.what other procedure can i use so that it clears for good?.14th October 2009 at 15:19 #41494VELGuest
i am facing a unusual problem in a site BTS is 2964,configuration is 6+4+6.1.5 yrs before i faced a rx diversity problem and i cleared that one,again today i am facing RX path imbalance fault code is 2A:57 i have checked VSWR,connectors and DRU’s still problem persist.i swapped that antenna and feeder cable with another cabinet now problem shifted to another cabinet.we are using 1800Mhz Band10th November 2009 at 07:00 #41495gtshiamoGuest
please can any one help ? i have this fault on RBS 2202, RX PATH IMBALANCE,
SO CF I2A 57
SO CF RU 4017th November 2009 at 20:19 #41496JrzlunaGuest
I had the same problem. the problem was the wind, it turn the azimuth antenna some degrees. you can see the variance if you move the antenna and waits for some samples. adjust both antennas to the same degree.
I hope it can help20th November 2009 at 11:21 #41497kerssusGuest
i need to get integrator for decode ericcson BSS equipement fault code,i hope somebody can help me.28th November 2009 at 07:46 #41498DeleGuest
Please i need a detailed document on ericcson oss to beused for fault resolution on the bsc.
Thanks17th December 2009 at 17:24 #41499vishalGuest
for al those facing rx path imbalance prob the best solution for it is to do a software update in the flash card this is to be done aft al the vswr, changing of the antenna andal is done… m sure u wont face the prob again ….29th December 2009 at 09:53 #41500AmarjeetGuest
Want know the DC power load of RBS 2964 BTS