Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Reply To: Tenor disconnect command

#27512
Saleh
Guest

thanks all for your replay

here is my current setup, i enabled the “disconnect supervision” is my config looks fine to you?

==================================

Unit
—-
Unit: 1
IP Address = 192.168.1.100
External IP Address = 66.66.66.66
Name = dammam-office

Online = 1
Relay ResetTime = 60
Relay Reset Number = 10

TcpKeepAlive = Disabled(0)

System
——
Country Value = 2
Country Code =
Area Code =
Minimum DN = 7
Maximum DN = 20
International Prefix:
1: 00
Long Distance Prefix =
Carrier Selection Prefix:
Intercom Used = no(0)
Private DN Used = no(0)
Interdigit Timeout = 4 sec.

Ring Frequency = 20 Hz(0)
PSTN Ring Sensitivity = Normal(0)

Disc Tone Frequency: 480 Hz (min) : 620 Hz (max)
Disconnect On/Off Time: 250 mSec(on) : 250 mSec(off)

Call Indication Tone = None(0)
Disable GUI = yes(1)

PSTN Trunk Group
—————-
PSTN Trunk Group: 1
Name = PstnPassThrough1
Pass Through = no(0)
PT Trunk ID = 0
Provide Call Progress Tone = yes(1)
Busyout = no(0)
Hunt Algorithm = ascending(0)
Modem Calls = No(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = Prepaid calling card
Ivr Card Digit Length = Variables
Disabled Voice Prompt 0
Ivr Preauthentication = 0
Ivr Language = None
MultiSession code: = None
IVR Access Number = None
Ivr Allow DID = no(0)
Ivr Answer Delay = 0
Retry Counter = 1
CID = From Interface(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery = none
2 Stage Dial = No
Translate Inbound Caller ID = no(0)
Relay Caller ID = yes(1)
IP Extension = no(0)
Maximum LAM Calls Allowed = 4
LAM: Index Pattern Replacement NumberType
Cas Signaling Type = loop start fwd disconnect(6)
Cas Orientation = user(0)
Dial Tone Detect = yes(1)
Dial Delay Timeout = 1000
Answer Delay Timeout = 0
Flash-Hook Signaling = no(0)
Supervision = disconnect(1)
Caller Id Detection = no(0)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:
unit# 1 line# 2: 1,2,3,4

PBX Trunk Group
—————
PBX Trunk Group: 1
Name = PbxPassThrough1
Pass Through = yes(1)
PT Trunk ID = 0
Provide Call Progress Tone = yes(1)
Multipath = yes(1)
Hunt Algorithm = ascending(0)
Modem Calls = No(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
Partial TG = no(0)
CID = Trunk ID(1)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery = none
2 Stage Dial = No
Translate Inbound Caller ID = no(0)
Relay Caller ID = yes(1)
IP Extension = no(0)
Public Number of Digits = 7
Private Number of Digits = 4
Public Hunt Ldn’s:
Private Hunt Ldn’s:
BDN: Index Bdn
Cas Signaling Type = loop start(1)
Cas Orientation = net(2)
Flash-Hook Signaling = yes(1)
Flash-Hook Min = 200
Flash-Hook Max = 700
Supervision = none(0)
Caller Id Generation = no(0)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:
unit# 1 line# 1: 1,2,3,4

IP Trunk Group
—————
Incoming IP call delete digits = 0
Incoming IP call prefix =
Outgoing IP call delete digits = 0
Outgoing IP call prefix = 00010
Prefix Trunk ID = no(0)
Default Trunk = No
External Routing Request = no(0)
Display Information ID = Tenor-Gateway

Line
—-
Line: 1
Law = uLaw(0)
Rx Gain = -8dB
Tx Gain = -6dB
Line: 2
Law = uLaw(0)
Rx Gain = 0dB
Tx Gain = 0dB
Guard Time = 0mS
DAA Start Up = Enabled

Gatekeeper System
—————–
Zone Name =
Border Element IP Address(prim) = 192.168.1.100
Border Element IP Address(sec) = 0.0.0.0
Discovery IP Address = 0.0.0.0
Gatekeeper Password =
LRQ returns all candidates(0)
Maximum LRQ Hops = 0
WAN Call Limit = 0 (disabled)
LCF/LRJ V3plus = 1
Gatekeeper Option Flags:
Use IP Header Address = no(0)
Ridgeway ARQ = no(0)

Border Element
—————–
Static Routing
Static Route #1
RouteName =
Gkmode = Destination is a Gateway (0)
CallSignalAddress = 80.80.80.80:1720
1:* Public LDN priority(1)
2:* Private LDN priority(1)

DSP

Voice Coding algorithm = 68
Voice Information Field size = 160 bits
Silence Suppression = Enable(1)
Minimum Jitter buffer = 60 msec
Maximum Jitter buffer = 300 msec
Receive Gain (PCM -> IP) = 6 dB
Transmit Gain (IP -> PCM) = 8 dB
Digit Relay = 0
Fax Relay Type = 0
Fax Maximum Rate = 144
Fax Playout FIFO nominal delay = 600
Fax Modem Coding = 0
Fax Modem Voice Information Field size = 0 bits
Idle Time = 30
Answer Supervision Options = 0
Disconnect Supervision Option = 1

H323 Gateway
—————–
Primary GK Address = 0.0.0.0
Primary Auto Discovery = 1
Secondary GK Address = 0.0.0.0
Secondary Auto Discovery = 0
H.323 ID = XXX
Register DN = Register as GW Prefixes(1)
Ignore Bandwidth in ACF = no(0)
Default H245 Tunneling = yes(1)
Round Trip Delay = 0
One Stage Dialing = 0
RRQ Interval = 0
H323 Interop Flags:
H225 GW Protocol = h323(0)
Do BRQ = 0
SlaveSessionId0 = 0
AllowFastStartOnly = No(0)
RRQv3plus= No(0)
ProgressInd Alert= No(0)
StartH245Flag= No(0)
Automatic Ext IP Update= Yes(1)
RTP Verification= No(0)

Do Lightweight RRQ = no(0)

==================================

thanks