Generic selectors
Exact matches only
Search in title
Search in content

Cisco ATA 186 in use on ADSL

  • This topic is empty.
Viewing 15 posts - 1 through 15 (of 16 total)
  • Author
    Posts
  • #25405 Reply
    Mujahid
    Guest

    anyone out there who could help me configure a go2call calling account onto a cisco ata186 device with the use of an adsl connection.
    Thanx

    #25406 Reply
    Noname
    Guest

    Mujahid, I tried several providers and all of them did not provide much help at all.Seting up the ATA was trouble after trouble.
    Tom, with DUAL Talk was the execption to the rule. First class help!!!

    #25407 Reply
    Fred
    Guest

    I bought a new ATA 186 but It is not working. My configuration table (http://IP/dev) does not have
    Gatekepeer or Proxy field( is missing ).
    Another problem is that I cannot get a dial tone on both telephone ports.

    How could I solve this problem ? Do I need a good firmware to solve the problem ? Please advise me where I can get the firmware or how I can solve this problem.

    #25408 Reply
    Tom
    Guest

    Try DUAL Talk. It’s a cheaper calling service.

    Instructions for configuring an ATA 186 for DUAL Talk are shown at dualtalk.com/ata186config.htx.

    #25409 Reply
    fernando
    Guest

    any body can tell me how to configure my ata 186 to be used with a direcway satellite service, or whether this doesn’t work with satellite. I’ve been trying with the net2phone configuration and go2call also with no results.

    thank you

    #25410 Reply
    Mujahid
    Guest

    Fernando,
    Check ur software version of the Cisco ATA 186 device. If it is less than 2.15 then u require an update before which u could use net2phone or go2call.

    any problems just send me ur configuration page attached to my email.

    #25411 Reply
    Christopher
    Guest

    I have 2.16 firmware but I cannot setup it with ATA 186. I emailed two timew the go2call support, but I receiver no answer. Can you give me more detailed instructions.
    I follow the instructions posted here http://www.go2call.com/docs/ciscoATASampleConfig.pdf but it doesn’t work.

    #25412 Reply
    Jesse
    Guest

    Fred, you need to have two lines assigned to the same ata in order for both ports to be functioning or, you can enable it in the setup, it is not on by def.

    #25413 Reply
    Dharmesh Gohil
    Guest

    I am having ciscoATA 168 but problem is that i am connecting telephone in phone1 and when i am pressing the configuration button it ll not apper any voice configuration manu so how can i asign ip address to ATA and i also dont knows that wht was the previous IP address of ATA..

    #25414 Reply
    ramkumar
    Guest

    I am having ciscoATA 168 but problem is that i am connecting telephone in phone1 and when i am pressing the configuration button it wasn’t not apper any sound. then i connect phone 2 also.i face same problem.what will i do.please help me.

    #25415 Reply
    sanjay chhabria
    Guest

    I have purchased new cisco ata186. I have connected it peer to peer with my pc. The first thing i wanted to ping it from my pc but when i press 20# it speaks some alphabets again i press 0 to disable and set ip add manually it only speaks alphabets pl help me.

    #25416 Reply
    Sean
    Guest

    I am having trouble setting up the network connection configuration for Net2phone on a Direcway connection. Any suggestions please

    #25417 Reply
    Dime Miovski
    Guest

    I have VOIP device CISCO ATA 186 with firmware software version 2.16.1. I’m using accounts from NET2PHONE . I have technical problems with connection. I have deal tone and after I pickup the telephone number I have busy tone on my line so I cannot make a call at all.

    #25418 Reply
    voiphelp.net
    Guest

    Hello Sanjay,
    Your ata186 is password protected. If you have firmware 2.15 you can factory rest it by picking up the phone, pressing the button on the top and keying in “factreset#” with your key pad and * to save. If you have firmware version 2.16 I’ve not heard of a good way to remove the password yet.
    support@voiphelp.net

    #25419 Reply
    andreas
    Guest

    I am having trouble setting up the network connection configuration for deltathree on a Direcway connection. Any suggestions please

Viewing 15 posts - 1 through 15 (of 16 total)
Reply To: Cisco ATA 186 in use on ADSL
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">