- This topic has 286 replies, 1 voice, and was last updated 14 years, 9 months ago by MikeM to Shayan.
8th March 2006 at 13:20 #23922AntonioGuest
Hello , i have a quintum Tenor CMS, i using him as GK ,until now i just receive in IPRG and send it to TCRG(E1) using Hopoff’s , my question is : Can i receive by IP and send again by Static Route without passing for TCRG.
i dont make any king of gw registration in my GK
Thanks in advance8th March 2006 at 18:18 #23923Yeyo_MexGuest
Hi, I want to establish a Tenor to Tenor Calls, where at point A I’ve an ASM200 connected to a PSTN line, at Point B I’ve an ASG200 connected to a Modem (FXS), over a Wireless Lan; I want to dial a number from the B side directly, I mean when I pick up the phone at the B side, I expected to hear the dial tone from the pstn line from point A (transparent call), wich will be the basic configuration, I’m all mixed up with the configuration, I used to use Multitech’s MVOIP series but this equipment are more complex.8th March 2006 at 20:09 #23924MikeM to YeyoGuest
If you have an actual modem connected to the FXS of the Tenor, and you want to do modem calls, I am not sure that that will work well. Yes, the tenor states that it supports modem calls, to a small extent, but I really do not think it works well.
If you mean that the modem is a GSM or CDMA device for mobile/wireless calls, then I can help you with the config and you can contact me at firstname.lastname@example.org March 2006 at 18:29 #23925Tareq MahmudGuest
I am using tenor ax series Gateway lost my password that’s why I cant login that Gateway .please what is the procedure break the password.
pls help me..
Tareq mahmud,MSN ID email@example.com
Cell:+88017675936418th March 2006 at 13:04 #23926Dele OrimsGuest
I have an ASG200 what can be done to upgrade the devise to ASM200 since it has all the neccesary ports18th March 2006 at 16:22 #23927NabilGuest
Hi all, how can I connect CDMA lines to my ROUTE is there any special devices I should be using?!! Now I have Quantum D2400 and A800 as wel as cisco 5350, please advise.Thanks.19th March 2006 at 03:14 #23928MikeM to Dele OrimsGuest
There is nothing you can do to upgrade this. While you may see the ports on the outside, the necessary hardware is missing inside the unit to support FXO connection. These units are not field upgradable.
Mike19th March 2006 at 03:16 #23929MikeM to NabilGuest
Most likely you can connect the CDMA device to your A800 if your CDMA provides an analog connection.19th March 2006 at 16:04 #23930Dele OrimsGuest
Hi Mike!! Thanks for the explanation. 234-803495317624th March 2006 at 04:23 #23931mvillarGuest
mike y have this same issue, did the port forwarding solve it
Rusty – 7 Jan 2005
I have a problem with a quintum A800,
Am able to receive calls through IP> PSTN but the PROBLEM is that the called person cannot hear the caller BUT caller can hear cristal clear.
Any solutions please?24th March 2006 at 04:29 #23932MikeM to mvillarGuest
It sounds like there is a firewall/NAT on your IP and it is not allowing voice packets through in one direction or you have not configured the tenor for answer supervision correctly and it is not send the connect message back to originator so that originator can open media path in both directions.
Mike11th April 2006 at 08:45 #23933mohamed asimGuest
We try to upgrade the Tenor ASM400 (sn=a012-103304) patch from (p103-08-08) to
(p104-12-00) by ftp client after it send all the (txt) (jbc) file and the tnrboot.bin
during sent the tnrsys.bin filt it stops then the tenor is restart and it not boot the normal boot that we know it give this message
It is only six available commands and it is a screen shoot from the quintum boot
best regards12th April 2006 at 12:38 #23934use vanguard320 for voipGuest
hello, ive installed a voip solution with sip, i used to have frame relay installed and i wanted to use again some motorola vanguard as FXS like linksys pap2, could annybody help me to configure it?
nacho18th April 2006 at 09:30 #23935GbengaGuest
Hi Mike, I have A800 but i cant make calls wih it. I have st the parameters that are required. I want it to pass through IP but each time i dial a numner it bounces back and gives me an engaged tone.Pls help i need to makecalls!!!18th April 2006 at 13:59 #23936MikeM to GbengaGuest
If you would like my assistance in troubleshooting this for you, please contact me at firstname.lastname@example.org.