Generic selectors
Exact matches only
Search in title
Search in content

what’s the procedure of send SMS in AXE?

  • This topic is empty.
Viewing 15 posts - 1 through 15 (of 72 total)
  • Author
    Posts
  • #37958 Reply
    Jinhua Dong
    Guest

    Hi, All

    I am a new guy to test Ericsson Axe, who can tell me the procedure while a guy send a SMS to another one, which Route is be used, B-Table, what’s the differences between Send SMS and Make a Call?
    The whole procedure is best.

    Thank you very much.

    E-mail is welcome.
    Jinhua_Dong@hotmail.com

    #37959 Reply
    Jack Sparrow
    Guest

    SMS is Non Circuit Related Service.
    Only processed through C7 Signalling Between GSM Nodes.

    Route to SMS-IWMSC will be Used for this they uses a special DEVICE TYPE = MSMO.

    Check in your ERICSSON Manuals.

    Print this Command.

    EXROP:DETY=MSMO;

    In the Printout there will be a BO=XX.

    ANBSP:B=XX;

    In this Origin only Barring is Dine if needed and charging case will be attached.

    Thats it.

    #37960 Reply
    Jinhua Dong
    Guest

    hi, Jack

    yes, i got the route which DETY=MSMO, and the route is with BO=93, but in B-table, analysis just got D&CC, then where will Exchange transfer SMS? how does he know? even he don’t SP of destination.

    one more question,
    in route table, there are
    DETY=GSMS MIS3=1 BO=91
    DETY=IWSMS MIS3=1 BO=92
    DETY=MSMO MIS3=1 BO=93
    DETY=MSMT MIS3=1 BO=94

    i think
    MSMO is for a SMS Originated
    MSMT is for a SMS Terminated
    GSMS is for What?
    IWSMS is for What?

    thank you very much, would you like tell me the interwork of relative blocks?

    #37961 Reply
    Jinhua Dong
    Guest

    hi, Jack

    i am so stupid, the SMS is know the SMS gateway’ GT address.

    but please answer my second question, thank you very much.

    #37962 Reply
    Jack Sparrow
    Guest

    It seems you are working in R10 Release and AXE810 Node.

    AM I correct ?

    In R10 They divided the SMS-Legs further for Traffic Calculation and Charging Purpose.Read it in ALEX.

    MSMO is for MS to SMS-IWMSC( MSC).
    MSMT is for SMS-GMSC to MS.
    GSMS is for SC to SMS-GMSC
    IWSMS is for SMS-IWMSC to SC.

    Rgds

    * You will soon get a mail from Me.

    Rgds

    #37963 Reply
    Jinhua Dong
    Guest

    Thank you, Jack

    How did you know i was working in R10? sure, you are right, is there any difference between R10 and other version?

    //Regards

    #37964 Reply
    Jack Sparrow
    Guest

    Yes the difference is :-

    GSMS is for SC to SMS-GMSC
    IWSMS is for SMS-IWMSC to SC.

    I read abt These two in R10 Delta.
    So I got you.

    Is it AXE810+APG40 ?

    or AXE810+IOG20 ?

    Rgds

    Jack

    #37965 Reply
    Jinhua Dong
    Guest

    hi, Jack

    you are so clever, ^_^. there are AXE10+IOG20, AXE810+APG40 two kinds in out country.

    i have another question. you know, in B-table, the result will got CC&D, if i don’t need CC&D, can i remove all data in BO=91&&94?

    DETY=GSMS MIS3=1 BO=91
    DETY=IWSMS MIS3=1 BO=92
    DETY=MSMO MIS3=1 BO=93
    DETY=MSMT MIS3=1 BO=94

    Can i make friend with you? i think you are a Ericsson Expert, if i have other questions, can i ask you?

    thank you very much!

    Rgds

    #37966 Reply
    iliana
    Guest

    Dear Friends,
    Would like to ask you what means MIS3=1 parameters.
    Please would you tell me what is exactly SMS routing from roaming subscriber? When I received my bill I saw as destination number our SMSC.
    Thanks
    Iliana

    #37967 Reply
    Jinhua Dong
    Guest

    hi, iliana

    MIS3=1 means Charging is performed
    MIS3=0 means Charging is not performed

    //Regards

    #37968 Reply
    Jack Sparrow…
    Guest

    Hi Jinhua,

    Yes you can Remove D and CC.But better keep it.Anyway you will be doing the Billing in Post Processing methode…where you can filter out iunstead of stopping generation of SMS-CDR.

    Rgds

    scorplund1976@yahoo.com

    Jack

    #37969 Reply
    Jack Sparrow—Hi iliana
    Guest

    Roaming susbcriber SMS will be sent to His HPLMN SMS-SC Server.

    So we can say Routing will be his SMS-SC Number.

    Rgds

    #37970 Reply
    Misa
    Guest

    Hi all,

    Plz help me, what is the procedure (step by step) for sending SMS in AXE by using WinFIOL?

    Brgds

    #37971 Reply
    iliana
    Guest

    Dear Friends,
    Thanks a lots for your response.
    Would like to ask when the subscriber in roaming and sends SMS, this SMS is routed to HPLMN SMS-C, but in which signalling message HPLMN SMS-C finds the destination address?

    #37972 Reply
    Roameo
    Guest

    Hi,
    The destination MSC-address is found in response to SRI-SM message (Send Routing Info for Short Message).
    enJoy,
    Roam..

Viewing 15 posts - 1 through 15 (of 72 total)
Reply To: what’s the procedure of send SMS in AXE?
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">