Erlang software tools...
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Subscriber info in AXE-10

Viewing 15 posts - 31 through 45 (of 65 total)
1 2 3 4 5
  • Author
    Posts
  • 7th April 2005 at 14:21 #36491
    sjp
    Guest

    I want to to decode the messages for “CCITT7 MTP2 TELEPHONY SIGNAL MONITOR” ptinout for C7MTI command. Specifically I want the documentation for decoding the failure codes and other values for different TUP messages.

    25th April 2005 at 04:25 #36492
    Ganesh
    Guest

    Dear all,
    Can any one help me in automatic routing of calls based on the asr of the routes.eg,say for trd 110,rc=9.rc 9 has got say 5 routes,r1,r2,r3,r4&r5.I would like to route the traffic fortrd 110,on these routes based on asr .suppose if asr of first route is 30% and second route is 40%,then calls should go in the 2nd route as first choice and so on.Pls explain me with detailed commands and explanation.

    10th May 2005 at 20:27 #36493
    Aly
    Guest

    In AXE10..In charging analysis..What does the parameter “EAE” mean ? How it is used ? And what is the recommended values ?

    25th May 2005 at 10:45 #36494
    Amit
    Guest

    Hi all
    Can anyone help me know the details about AXE traffic cases and Mobile traffic cases?

    1st June 2005 at 16:20 #36495
    MIRCEA CATRINA
    Guest

    In the AXE-10 exchange, how to replace in A-number(for E1 PABX in R2) ?
    EXP:
    599 replace with 502200
    Regards

    5th June 2005 at 05:00 #36496
    dheeraj
    Guest

    Hi all,
    can anybody tell me about the commands used in ERICSSON AXE 10
    for ILD & NLD.

    9th August 2005 at 10:45 #36497
    Nick
    Guest

    Can anyone know how pulese metering is done on PRI/ISDN lines connected with AXE 10 for VoIP. There is huge differecne in pulse metering volume and volume calculated from CDR generated by VoIP GW.

    Best Regards

    4th December 2005 at 12:13 #36498
    Mr. Inquisitive
    Guest

    Does anybody have an idea on the data format used to store subscriber’s information in HLR.

    16th December 2005 at 03:04 #36499
    Tuan
    Guest

    Use this command : mgssp:imsi=xxxx; in your MSC/VLR

    21st December 2005 at 20:58 #36500
    farshid
    Guest

    Hi all,
    plz help to finde abbriviation of (um) interface bettwen ms and bts
    any body know about um abbriviation ?thx

    17th February 2006 at 09:49 #36501
    Viet
    Guest

    i want to know max value of NI in SAE=500,block =liv5g?
    do this value depend on APZ?

    thanks very much.

    17th August 2006 at 21:26 #36502
    Ralph
    Guest

    Does anyone know the HLR command to find the number of subscribers which are provisioned to use a particular APN?

    17th August 2006 at 21:30 #36503
    Ralph
    Guest

    Does anyone know the AXE10 HLR command to find the number of subscribers which are provisioned to use a particular APN?

    18th August 2006 at 20:19 #36504
    WizzurD
    Guest

    Does anyone have any command to view location area info apart from MGSSP:imsi=XXXXXXXX;

    2nd September 2006 at 14:45 #36505
    Sweety Skaria
    Guest

    Dear all,

    Wishes! I have just joined a mobile operator. I am working in the Switch. I have no training. I am made to work with WinFIOL (Ericsson).

    How do I start with? Thank god I know the basics of GSM. Please refer some sources, other than ALEX. I would be grateful if you could send the details to the below mentioned mail.

    kingthemate@yahoo.com

    Regards,

    Sweety

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 65 total)
1 2 3 4 5
  • The forum ‘Telecom Design’ is closed to new topics and replies.