- This topic has 25 replies, 1 voice, and was last updated 10 years, 8 months ago by Mak.
19th August 2010 at 07:54 #64043MakGuest
Please elabrote Power control works on BCCH or Not?19th August 2010 at 10:31 #64044Huawei – ManGuest
Power Control is for Non-BCCH TRXs, not for BCCH TRX. BCCH is control channel, its serving can’t be limited by PC.19th August 2010 at 11:17 #64045MakGuest
Yeah, its ok. If you have check any log file you will found the 2 different Rx levels of a particular cell. The First one Rx Level is some degraed than the 2nd one signal strenght.19th August 2010 at 11:53 #64046Fresh OptGuest
what’s the role of parameter PWRC in ALU. It’s disabled by default, should we enable that. And, what’s the difference between PWRC and EN_BS_PC.
Fresh Opt19th August 2010 at 12:39 #64047Huawei – ManGuest
You can see 2 different RxLevel on the same cell, only on the following cases:
MS1 is in Idle Mode (it is BCCH RxLevel which PC is not used)
MS2 is in dedicated Mode (it is Non-BCCH TRX RxLevel which PC is used)
PC is used for reduce UL/DL Interference, to save BTS/MS battery life etc.19th August 2010 at 13:10 #64048MakGuest
I have seen the different RX level of a cell at the same time and same MS in dedicated mode only.19th August 2010 at 13:30 #64049RexGuest
it happens when DTX is activated. With DTX on RxLev_Full is different with RxLev_Sub. With DTX off they are equal.
Rex.19th August 2010 at 17:14 #64050pixGuest
pwrc is used to remove the samples of DL RXLEV measured while the TS is hpoping on the BCCH frequency.
This is only useful if cell is BBH.
the ms is on trx3, ts2.
there are 3 trx in the cell.
the cell is hopping on 3 frequencies (that’s bbh !)
everytime the trx3/ts2 is hopping on frequency 1 (rather than f2 or f3), then the rxlev is high (becauser there is no dl pc on the DL for the f1)
to avoid getting a crazy average (f1 good, f2 and f3 low because of dl pc), then you should use PWRC.
pix20th August 2010 at 05:06 #64051Huawei – ManGuest
I agree with Mex, except one thing.
When DTX is activated, there can be difference.
But without enabling DTX, MSs can have different RxLevel also in dedicated mode when PC is enabled.
DTX-it is not a changeable feature, you can enable or disable. It is used only in silent call (uplink or downlink).
PC-there are many parameters in PC to change. PC is used according to RxQuality, RxLevel. And you can change their thresholds.20th August 2010 at 05:07 #64052Huawei – ManGuest
Sorry, Rex. I mentioned mistake your name20th August 2010 at 14:01 #64053Fresh OptGuest
Thanks Pix, now is clear.
Fresh Opt20th August 2010 at 14:15 #64054RexGuest
No problem. I thought that Mak said there is only one MS in dedicated mode and seen different RxLevel at the same time. As I understood 2 different levels (Full and Sub) in the same time and thought maybe DTX is activated. Did you mean without DTX, RxLevel_Full is different with RxLevel_Sub?
Rex23rd August 2010 at 04:59 #64055Huawei – ManGuest
I mean: two different mobiles can have different RxLevel if one of them is in Dedicated Mode and second one is in Idle Mode. I’m talking about Power Control. In this case doesn’t matter DTX is enabled or not.
We can take into account DTX for the same Mobile. When you have silent call you should look at RxLevel_Sub, when you have bi-directional active conversation you should look at Rxlevel_Full.
DTX is enabled: RxLevel_Sub
DTX isn’t enabled: Rxlevel_Full
Is it clear what I mean 🙂 ?23rd August 2010 at 05:05 #64056Huawei – ManGuest
If both Mobile Phones are in Dedicated Mode when Power Control is enabled:
MS1 is in BCCH TRX (PC will not work)
MS2 is in Non-BCCH TRX (PC will work)23rd August 2010 at 06:06 #64057MakGuest
Yes I am talking about the same MS is having the different Rx Level. If you See the Serving and Neighbors window in the drive test tool. Like the below example.
Cell Name BCCH BSIC Rx Level
Cell1 121 47 -85
Cell1 121 47 -65