Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

RX Quality Issue

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #63955
    Arvind
    Guest

    I got 1 issue in GSM site…

    In this site particular sector facing RX Quality issue.There is no nearby neighbour sites for 5km facing this sector..
    I have tried these steps
    1.Tilt given
    2.No hardware issues
    3.No VSWR
    4.Checked with Swapping TRX
    5.No Cable swap.
    6.With Reference to TA report tilt given

    What can be done after this?Pls Suggest….

    #63956
    Lex
    Guest

    Have you checked the interference report?
    Which vendor?

    #63957
    jaihu
    Guest

    for such an isolated site u can go for

    -of course look for interference sources thoroughly,
    -increase coverage by increasing power
    -check the buildings in front of this sector
    -if high buildings exist, and power increase doesn’t help then, change of the site location might help

    #63958
    Mania
    Guest

    When you say RXQuality issue, do you mean bad RX Qual in field / in HO Stats on in RMS stats, Please clarify.
    In any case is it effecting one radio / one band / all hopping etc, pls specify which is worst hit. check from frequency point of view.

    #63959
    Arvind
    Guest

    Vendor :Huawei

    Band:1800

    issue is with hopping frquencies,checked with HSN and MAIO plan.

    #63960
    Alexia
    Guest

    with SFH normally you can have bad rx quality but the SQI is good and the customers can hear each other well. which problem do you really face??

    #63961
    Ashvaan sheik
    Guest

    Assalaamualaikum…!!

    some sites can overshoot above 5kms also
    so check it out.. Check coverage level.. if there is a lake or river near by then interference occurs due to TIR..check whether nieghbours are properly defined.. there can be a problem of handover failures,,, or change the orientation little bit.. then do post drive and observe..

    #63962
    MAMAD.SAED
    Guest

    RX- QUALITY (UP LINK ) LOW . SOLOUTION .PLEASE HELP ME

    #63963
    pix
    Guest

    .REDUCE DOWNLINK TX POWER.

    #63964
    MAMAD SAED
    Guest

    IN THE HUAWEI HAVE( TCH ass FR ) TO SOLVE THIS CAN YOU HELP ME WHATS YOUR SOLUTION?

    #63965
    rakesh patel
    Guest

    plz.. suggest

    #63966
    Subhakanta jena
    Guest

    If Rx level is good but Rx quality is bad.Then what is the reason behind it and how to solve this.Also plz give some idea about pilot pollution

    #63967
    Lemaure
    Guest

    Hi Subhakanta jena
    Good Rx level and bad Rx quality is due to interference as know in GSM/LTE or pollution in WCDMA systems;
    the latter is due to many servers having almost the same signal strengtht without any being significantly dominant compared to the others (usually more than 5 radiolinks) and all of them being low.
    to fix it you just need to create a dominant server thanks to physical actions on site and neighbors. Also make sure radio parameters are not incriminated (wrong location/mobility parameters like CIO,Qoffset,…)

    #63968
    sachin tyagi
    Guest

    Guyz,

    firstly in 2G there is no pilot pollution, we can relate the term as UL and Dl interference,
    if we are having good Rx level but Rx quality is poor then below are the resons behind it.

    # Same BCCH or TCH pr BSIC will be there.

    # Some cells are overshooting at that place.

    # UL and DL interference may be worst which will be found in Reports 196,210 in Nokia.

    #Check SQI and BER .

    # TCH interference was there which will be found in live BSS .

    #UL and DL interference may be due to some hardware issue or any external source

    Thanking you

    any issue mail me on

    Sachintyagi720@gmail.com

Viewing 14 posts - 1 through 14 (of 14 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.