Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

8150 FAULT IN UNIT UltraSite NOKIA

Viewing 5 posts - 1 through 5 (of 5 total)
  • Author
    Posts
  • #46376 Reply
    patrick
    Guest

    i have this alarm:

    My site ok, everything is ok except this default:

    BCF-035 COMM 2006-12-14 18:00:22.30

    *** ALARM TRE -001
    (15844) 8150 FAULT IN UNIT UltraSiteBTSHub FXC E1/T1 m Unit Symm
    02 4080d 01 5d

    who has a explanation?

    thx for your help.

    #46377 Reply
    M@steR
    Guest

    8150 FAULT IN UNIT

    Meaning
    A piece of equipment has detected a fault in its operation.

    This alarm affects the provided services.
    Supplementary information fields
    1 01 BSC supervises the equipment
    02 BTS supervises the equipment

    2 Q1 address of the piece of transmission equipment

    3 the functional entity number specifies a physical unit of the
    transmission equipment, for example a plug-in unit or a
    daughter board. The number can be 0…254

    4 the supervision block number specifies the faulty part of the
    functional entity, for example a certain line interface or
    component

    5 number of the Q1 service channel in the BSC, 0…27.
    If equipment is supervised by the BTS, the channel number
    is not relevant

    6 name of the piece of transmission equipment.
    Not included if the name is in the alarm object field of
    the alarm printout.
    See alarm instructions

    7 number of the piece of transmission equipment.
    Not included if the index is in the alarm object field of
    the alarm printout.
    See alarm instructions

    8 rack (cabinet) number
    FF = not defined
    Included only if the equipment is supervised by a BTS that
    supports coordinate settings

    9 shelf number
    FF = not defined
    Included only if the equipment is supervised by a BTS that
    supports coordinate settings

    10 slot
    FF = not defined
    Included only if the equipment is supervised by a BTS that
    supports coordinate settings

    Instructions:
    Check Supplementary information field 1 to see whether the BSC or
    the BTS supervises the equipment.

    If the BSC supervises the equipment, use the MML commands Axx for
    alarm administration.

    If the BTS supervises the equipment, use the MML commands EOx for
    alarm administration.

    To clarify the reason for the fault, take a remote session to
    transmission equipment and display fault information.

    See the equipment operating manual for more detailed information on
    the fault code and corrective actions.

    Cancelling
    Do not cancel the alarm. The system cancels the alarm automatically when
    the fault has been corrected.

    #46378 Reply
    patrick
    Guest

    On NOLS,i also have this explanation:

    The alarm cannot be cleared by replacing the transmission unit.
    No correction is needed for the BTS SW.

    Replace the transmission subrack or RECALIBRATE THE INTERNAL OSCILLATOR in the transmission card.

    What does it mean’s?

    How recalibrate the INTERNAL OSCILLATOR on the FXC E1/T1??

    #46379 Reply
    Alonewolf
    Guest

    Simply give the BCF one munite hard reset (lock the BCF then cut its electricity), observe the alarm again,

    #46380 Reply
    parmeshwar
    Guest

    how to clear fault in unit alarms

Viewing 5 posts - 1 through 5 (of 5 total)
Reply To: 8150 FAULT IN UNIT UltraSite NOKIA
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">