- This topic has 58 replies, 1 voice, and was last updated 17 years, 1 month ago by ESB for 2216.
-
AuthorPosts
-
7th April 2006 at 20:59 #44763Erkan OkayGuest
Hi,
In ancient times (circa 2000) I used to work with Ericsson BSS. There were three CDU types: CDU-A, CDU-C and CDU-C+. There were RBS 200 and RBS 2000 family. Now I’d be more than happy if somebody updates me with the new BTS types and CDU types.
7th April 2006 at 21:21 #44764weberGuestHi Erkan Bey,
Now-a-days we are using mostly RBS2206. With CDU-G, CDU-F..
Other than that we have WCDMA RBS3202 or RBS3206.
Hope this helps,
Gurusuruz..;)
7th April 2006 at 21:26 #44765Erkan OkayGuestThanks a lot for the update, weber! I guess you speak Turkish or you are Turkish. Which one?
20th April 2006 at 10:23 #44766karma wangchukGuestWhat was the different between RBS 2202 and 2206?Apart can you tell me
different types of CDU and their usage.and also why -ve voltage is a
nominal voltage in the communicatiion?and what is the different between TRU and DTRU? with this message hpoe you will send detail of above mention.and i will be expacting you that you will send details that i have mention above…21st April 2006 at 21:29 #44767PavelGuest2202 – is a small capacity indoor RBS with maximum configuration 2+2+2. In case of adittional cabinet in can be extended up to 4+4+4.
2206 – large capacity RBS with maximum 4+4+4 configration in standart cabinet.
As I know -2202 is quite old version of RBS2000 series. 2206- is newer one.
Differents of all CDU types is maximum output power per TRU.
Difference between TRU and dTRU, is that dTRU -is duplex TRU. Actually it is 2xTRX in one TRU.21st April 2006 at 21:34 #44768PavelGuestAdittionaly(fom official E/// info):
CDU – Combining and Distribution Unit
The CDU is the interface between the transceivers and the antenna system.
All signals are filtered before transmission and after reception by means of
bandpass filters. The CDU allows several dTRUs to share antennas. There
are a maximum of three CDUs in one RBS 2106.
The CDU combines transmitted signals from several transceivers, and
distributes the received signal to several transceivers. The CDU is
hardware-prepared to support EDGE. Two different CDU types are used in the
RBS 2106 to support all configurations:
• CDU-F is a filter combiner intended for high capacity solutions.
• CDU-G can be configured either for high capacity or for high coverage. It is
a combiner that can be used for synthesizer hopping.
Number of units: 1 – 31st May 2006 at 12:12 #44769SharifGuestHow can i know the total structure of GSM.
15th February 2007 at 21:59 #44770kennethGuestRBS2202 can be maximized up to 6+6+6.. 1 cabinet per sector
28th February 2007 at 09:36 #44771ivandgreatGuestWhats the difference between RBS3202 and RBS3206? Can anyone help me about Ericsson WCDMA. Thanks a lot !!!
1st March 2007 at 16:28 #447723000GuruGuestRBS 3202 is the older indoor WCDMA cabinet and RBS 3206 are the new generation outdoor cabinets.
Cheers
3000Guru
1st March 2007 at 23:26 #44773kenGuestand RBS3202 can now be upgraded into HSDPA capable node.
15th March 2007 at 11:41 #44774ghayhabGuestWold u plz inform me how i can use RBS 2206 334 configration and whate the cabling in use
17th March 2007 at 08:27 #44775finnGuesthi ghayhab,
if you will be using dTRU Hybrid Combiner you will be using around 18 Rx cables between dTRU and CXU and this will include between CXU and CDU plus 9 TX cables between dTRU and CDU and 4 TX1+TX2 Hybrid Combiner cables for dTRU 2, 3, 4 & 5 (note dTRU 0 is uncombined). configure your IDB using dTRU Hybrid Combiner, then select 3+3+4 for your SCC.
goblydegook luck!
17th March 2007 at 16:26 #44776ghayhabGuestThanx
28th March 2007 at 09:11 #44777ghayhabGuestthank you dear:
but i need graph for coniction cable bittwen CDU &CXU & DTRU for 3 3 4 configration from 2206 RBS
best regard &Thank you for support -
AuthorPosts
- The forum ‘Telecom Design’ is closed to new topics and replies.