- This topic has 206 replies, 1 voice, and was last updated 14 years, 4 months ago by Sabuz.
11th July 2003 at 08:36 #22753LjuboGuest
What is the max/avrg ASR that could be reached by Tenor A800
IP -> Tenor -> PSTN21st July 2003 at 15:15 #22754donGuest
Hi! I am configuring Tenor A800 behind a router. I have Dynamic IP ASDL connection. Please tell me if this is possible. Out-going calls are fine but the incomming calls are not going thru. Please tell me brand and model of router to buy (cheap with good quality). Thanks!!!21st July 2003 at 16:31 #22755MattGuest
I’ve got experience working with quintum and other voip gear. Ask me if you’ve got any questions.24th August 2003 at 13:51 #22756anandGuest
how to configure tenor to originate a call on pstn of one tenor to another. (fyi:it could already configure for ip – tenor – pstn )29th August 2003 at 19:13 #22757JorgeGuest
I can help me. I have an A400, need conect this to cisco 5350 located in other site. A400-IP-Cisco.10th October 2003 at 16:58 #22758ShahGuest
Can Any one tell me if I can Use 512kbps ADSL for tenor A400 please!
Thanks a Million!11th October 2003 at 13:54 #22759HwykingGuest
yes u can28th October 2003 at 17:49 #22760Shah SadequeGuest
Can anyone help me please.
I need to know How to confiqure Tenor A800. I never used Tenor. Basically I want to accept call from netmeeting. A step by step Guide will be Higly Appreciated.
Shah8th November 2003 at 19:14 #22761Hi DonGuest
Am in the same situation as you are. My provider is giving only one IP address per adsl of 512/128 kbps. I am setting up one A800 for t e r m i n a t i o n and the fixed IP will sit on the router. How then do I configure to enable a fixed IP on the gateway?
Any help will be much appreciated.26th November 2003 at 13:19 #22762SuzanGuest
I have a Quintum Tenor A800 gateway and 8 telephone lines.
If anyone would like to help me , I need to know step by step procedure to configure the Tenor A800. I can get link/bandwidth by using DSL modem. Please help and in return I can help you with Cisco products configuration.27th November 2003 at 07:13 #22763www.blue-lava.co.ukGuest
When configuring the Quintum A800 stay away from the GUI, nothing useful can be done here. Everything should be done from the Command Line Interface (CLI). Although this initially seems quite daunting the commands are broken up into logical sections, one for the pstn interface, another for the dial plan etc.
The simplest way to start is to use somebody elses working configuration, a complete print out of the settings can be obtained by typing in the following at the root level CLI prompt:
> co [return]
> print [return]
I have a number of working configurations for the A800 that I can mail you – this will get you up and running quickly. Please send your contact details to me at: firstname.lastname@example.org , I will forward you some configs by return.
You mention that you are using a DSL link for the A800, remember that if you are using G.729 you would require a minimum of 150.1kbs for eight simultaneous calls (this presumes a 30% silence suppression). This can be taken down as low as 74.8kbs if you install the PacketSaver option on your A800, although it does require that PacketSaver is also installed on the gateway you are sending to or receiving from.
Hope this helps.17th December 2003 at 14:40 #22764JGarciaGuest
Can anybody help me with an A800 configuration I have 256Kbps ADSL and the Tenor is in a LAN. I do not have a PUBLIC IP for this Tenor.
Thanks.20th December 2003 at 14:43 #22765AlbertoGuest
Hi, I have Tenors A800 as well as some D3000. It is my impression that the order in wich the config is made and saved (submit) affects the overall config. I say this because some times I have configurations running smoothly, and if I made a small change, say… disabling one channel, after submitting calls are not longer accepted by the gateway. Have anybody else had this same problem?20th December 2003 at 21:22 #22766HwykingGuest
If u have ADSL connection you should have a public IP address unless you are on a private LAN, at this point you can not configure tenor to process calls with a public IP…good luck…
Hwyking@comcast.net12th January 2004 at 01:07 #22767KrishGuest
I ahve a tenor a800 and a a400 and wish to connect it to a linksys DHCP router/firewall. This linksys has fixed Ip currently. Can someone tell me how to setup the the linksys. Do I use the fowaring with port numbers?