- This topic has 43 replies, 1 voice, and was last updated 13 years, 5 months ago by
Gokul.
-
AuthorPosts
-
8th September 2009 at 12:26 #58778
Kryshka
GuestHi,
We are using Ericsson equipment and encountered with the problem that MS do not response to Immediate assignment and also not send SABM message to MSC. This problem directly reflects on SDCCH establishment rate (sdcch fails due T3101 expire) and we have many customers complains due accessibility. CCCH, SDCCH resources do not perceive any congestion, interference, BSIC conflicts, signal levels in MS -75dBm.
Any ideas?8th September 2009 at 12:42 #58779Bijoy
GuestMake RACH Access Level Min. to -109 and check
8th September 2009 at 13:14 #58780Kryshka
GuestNow is -110. Does it make a difference?
8th September 2009 at 15:12 #58781RG
Guest1.) Whats the timer value for T3101. If it is greater then 3secs then it is fine.
2.) Any uplink interference (check IB report).
3.) Replace the hardware if there is no issue on the Um and Abis interface.
8th September 2009 at 15:28 #58782Krishka
GuestT3101 – 4 sec.
ICM measurements – no uplink interference;
With hardware – maybe, but observed in whole network.
The interesting thing, that in Air-interface trace(did recording with NEMO) shows, that phone replies to paging with RACH, and from the network receives Immediate assignment, and later nothing. Network repages, – the procedure repeats, but stops in the same place – no answer to immediate assignment. Isn’t clear why phone do not try to choose SDCCH11th September 2009 at 08:37 #58783ATTO
GuestHi Krishka,
How to check for the value of T3101 In Ericsson? also how to change the actual value? I do not find any command to check for.
Thanks in advance.
11th September 2009 at 09:31 #58784Kryshka
GuestWe did it by the requesting to ericsson, because the timer value cannot be changed by some command. But actually we didn’t see any significant improvement – huge number of sdcch fault due timer expire. The mobile do not answer to immediate assignment.
11th September 2009 at 11:24 #58785Bijoy
GuestChanging T3101 will not help
Change Rach Busy threshold to 5
Change RACH Error Threshold to 20012th September 2009 at 11:01 #58786Kryshka
GuestHi Bijou, where should be defined such thresholds and what impact they can do for immediate assignment? From my point of view – there are no problems with RACH establishment – BSC responds to RACH and sends immediate assignment but MS do not configure and send SABM message on SDCCH. Did you have problems similar like that?
Thanks12th September 2009 at 11:45 #58787Kryshka
GuestI do not find such parameters in Ericsson Cell describtion…
14th September 2009 at 05:20 #58788Bijoy
GuestHi kryshka
What is the value of Tx-integer in your system.Increase it & check14th September 2009 at 09:36 #58789Kryshka
GuestTx integer is 32. Previously it was 20, but the changes didn’t have results. If looking to rach establishment statistics – it’s really normally – more that 99%.
14th September 2009 at 10:17 #58790Bijoy
GuestActually,this is a normal Rf phenomenon.That is the reason we have this Max. no. of retransmission parameter to safegaurd immediate assignment.Since RACH is slotted aloha,there will be huge losses inevidently
14th September 2009 at 10:49 #58791Kryshka
GuestWe have MAXRET=4 in one BSC, and MAXRET=7 in second. No big difference. So, my though is something strong in the MS side, – he get all that he want from network side – channel assignment in immediate assignment message. If MS do not understand that message, – he replies with immd.ass. reject, or waits for second time. In our case, he waits 4 times and later – nothing. Why he do not react to imme.assignmt…
15th September 2009 at 04:26 #58792Bijoy
GuestHi Kryshka.
MS doesn’t give imm assignment reject.It is send by BSC under 3 conditions:
1.no available channel
2.channel activation failure
3.channel activation timeout -
AuthorPosts
- The forum ‘Telecom Design’ is closed to new topics and replies.