- This topic has 28 replies, 1 voice, and was last updated 7 years, 1 month ago by LEMAURE.
-
AuthorPosts
-
10th July 2009 at 12:24 #56570syeedGuest
check azimuth and tilt
10th July 2009 at 14:36 #56571OptimiserGuestThe difference in power between 1800 and 900 cells is usually like 10dB, so if u got like a twin layer, trafic will normally be on 900 cells. What you do is:
-favour intialisation on the 1800 cells, e.g. putting a Cell Reselect offset on them (14, 16, 20, 24, 30, etc, depending on the % of trafic you want on this layer).
-Maintain the trafic on the 1800 cells and favour HO towards them: increase HO_margin from 1800 to 900 cells, and decrease from 900 to 1800 cells.21st August 2009 at 16:14 #56572YuvalGuestI know of a company that have a solution for that specific problem. It is a dynamic carrier management system that makes automatic interventions based on the load – like an auto pilot, and fix this problem. We tested it, and it worked very well, but was too expensive for our CEO, and we were asked us to find alternative solution (but still no luck).
Let me know if you need more info.
22nd August 2009 at 09:12 #56573NITINGuest900+1800 SEG LEVAL,UL/DL QAL.NOT IMPROVE ANY PERAMETER NEED TO CHANGE
26th August 2009 at 17:43 #56574zyotiGuestHI timz,
i have one option,
first make your Min RX lev of 1800 layer to 75 or 85dBm and make CRO to lagge amount as. 30 to 40 dBm ( i know u say it unhealthy pulling traffic) but remember i have put access leve to 75 to 80 dBm so that good level of strength is achived, this enable the near all traffic(indoor and outdoor ) to clamp in 1800 with required rx lev then, also modify the HO PBGT and HO RX Lev accordingly , iam sure it will work… Hope this will help u
20th August 2010 at 10:48 #56575selaGuestcan someone explain to me how this Huawei GSM paramter means: AMR TCH/H Prior Cell Load Threshold(%)
21st August 2010 at 22:04 #56576AlexiaGuestHi Sela,
If you have installed Huawei BSC6000 LMT on your machine just log in and press F1 (To get Help page) then search for that parameter..and any other parameters. You should be able to understand something.18th November 2010 at 10:42 #56577selaGuestCan someone help me to know how i can control how much percentage of traffic is to be on half rate and how to be on full rate
26th November 2010 at 08:45 #56578bGuesthi sela
TCH Traffic Busy Threshold(%)
Default value is 60
Modify according to ur needs, but i recommend u 8027th November 2010 at 14:29 #56579selaGuestThanks
18th April 2012 at 07:12 #56580TYsGuestHello.
I want research Balance traffic in GSM. How can i get the document tell about it?
12th August 2015 at 08:18 #56581Mwiya WGuestHow do push voice traffic from 900 to 1800 band on common BCCH cell?
16th March 2017 at 12:38 #56582kitururuGuestHow to balance traffic on Huawei MBC cells?
What parameters can i tune to shift from 900 to 1800 ?
18th March 2017 at 06:47 #56583LEMAUREGuestHello!
some useful parameter to consider
IDLE MODE:
CRO (higher values on 1800)
DEDICATED MODE:
Layer (Higher value on 1800)
HO Layer Threshold (Lowest value on 1800) -
AuthorPosts
- The forum ‘Telecom Design’ is closed to new topics and replies.