Generic selectors
Exact matches only
Search in title
Search in content
Search in posts
Search in pages

SDCCH DROPS on Ericsson

Viewing 15 posts - 1 through 15 (of 18 total)
  • Author
    Posts
  • #54092 Reply
    EugeZ
    Guest

    Hi Guys,

    I seem to have a lot of cells with HIGH SDCCH drops leading to Low CSSR.

    Kindly advise me what i should do to reduce this.

    #54093 Reply
    pix
    Guest

    eugeZ,

    we talked about this a lot in this forum already.
    check HW status (exchange TRX, check path balance, …), interference, coverage, or perhaps some problems of authentication or ciphering during the SDCCH phase (core network issues, involving MSC or HLR)

    regards
    Pix

    #54094 Reply
    EugeZ
    Guest

    Thanks Pix,

    I think i missed your earlier discussionon this issue.

    My understading is that SDCCH drops are caused by poor RXQUAL, TA,signal strength, & Hardware.

    From the business objects tool most cells have SDCCH drops due to other reasons.

    This includes hardware. what kind of checks do we need to do to this hardware in order to solve the problem?

    #54095 Reply
    SA
    Guest

    Hello EugeZ.

    I think that you work with an Ericsson network so I would base my answer on that.

    There are 2 known formulas for the SDCCH Drop:

    CNDROP/CMSESTAB

    and

    (CNDROP-CNRELCONG)/CMSESTAB

    The second formula corresponds to the TCH Congestion excluded. So, the first formula really goes off the limit when there is congestion.

    The reason counters are the following:

    CDISTA: Excessive TA, that is if the TA value at a dropped connection is higher than or equal to the cell parameter TALIM.

    CDISSS: Low signal strength in downlink and/or uplink per cell (CDISSS or CDISSSSUB), that is if the signal strength is less than the BSC exchange properties LOWSSUL and LOWSSDL in uplink or downlink respectively, or in both the uplink and downlink.

    CDISQA: Bad quality in downlink and/or uplink (CDISQA or CDISQASUB), that is if the radio link quality is less than the BSC exchange properties BADQUL and BADQDL in uplink or downlink respectively, or in both the uplink and downlink.

    As you can see the Reasons also depend on the parameter configuration of the TALIM, LOWSSDL, LOWSSUL, BADQDL and BADQUL. Maybe you can check the values and consider to move a couple of them and after check the new distribution.

    You are right. The Other reason is normally around 70% – 75% in the Ericsson networks that I have seen.

    The SDCCH Drop can be improved by:
    – Adjusting the LA border so the interaction is minimum.
    – Using parameters such as the ACCMIN, CCHPWR and/or MAXTA. But be careful with the coverage and some complaints.
    – Better antenna performance. Remember to use electrical tilt (if possible) instead of too much mechanical.
    – In you have a MSC in Pool and High SDCCH Drop check if there is any issue with the synchrony.
    – I turned off the SDCCH HO (SCHO) and it worked in some sectors. Maybe you can try that.

    Regards,

    SA

    #54096 Reply
    S. OLSEN
    Guest

    SDCCH Drops Ericsson:

    Does anyone have a breakdown for the specific reasons for Ericsson SDCCH drops due to ‘OTHER’?

    It is well known T200 time out is one of the events to trigger? Any others?

    #54097 Reply
    MUIDEEN
    Guest

    causes of TCH congestion

    #54098 Reply
    Mr.David
    Guest

    Bad Transmission due to weather

    #54099 Reply
    Puneet
    Guest

    I seem to have a lot of cells with HIGH TCH drops by the reason of uplink Bad Quality and Suddenly drop in Ericsson.

    Kindly advise me what i should do to reduce this uplink Bad Quality and sudden drop on the cells?

    #54100 Reply
    Bijoy
    Guest

    HI Puneet
    UL Bad quality-check for CDMA/external interference/Hardware issues

    Sudden drop-check for coverge & HO issues first.

    #54101 Reply
    SDCCH Drop Signal Strength
    Guest

    SDCCH Drop Signal Strength

    #54102 Reply
    T-Max
    Guest

    Hi All,

    Could you help me what are the parameters to take care if we have low PSR(Paging success rate) & LU(Location Update)on Siemens and Huawei network? even we have already done some adjustment on LA boundary and checked that one LAC is only for one BSC ; and no cell have same couple BSIC/BCCH.

    Thank’s in advance for your collaboration.

    regards!

    T-Max

    #54103 Reply
    naquash ahmed
    Guest

    In huawei, we can achieve good PSR by adjusting the parameter “Rach min access level”.

    #54104 Reply
    Jeff
    Guest

    Hi naquash ahmed,
    How do you improve Paging Success Rate by tuning RACH Min.Access Level??
    Need some help here.

    #54105 Reply
    safar
    Guest

    hi ahmed ‘

    Is it really by tunning rach min acc have improved sd drop in ur network?plz explain its interesting…

    #54106 Reply
    senthil kumar.K
    Guest

    How blank call issuse/ call drop occurs in particular site are area.

Viewing 15 posts - 1 through 15 (of 18 total)
Reply To: Reply #54097 in SDCCH DROPS on Ericsson
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">