- This topic has 16 replies, 1 voice, and was last updated 17 years, 11 months ago by
MP.
-
AuthorPosts
-
5th September 2005 at 01:29 #42111
Amberish Trivedi
GuestHow Inter CBSC Soft Handoff is defined in Motorola system..i.e they are using type 4, type 7…but when we kn use which type?
5th September 2005 at 17:15 #42112khan
Guestgive details of rf plaining of cdma
6th September 2005 at 01:29 #42113amberish trivedi
Guesthi khan/… we are using 2 set of frequencies…so when my call is going from 1 sector of 1 site to another sector of 2nd site then they are defining this handoff as a soft if these sites are controlled by same CBSC but if they are handelled by different CBSC then they are defining it as ICSHO4 or ICSHO7…this much i kn say you…awaiting for ur reply
3rd March 2006 at 07:39 #42114Santy
GuestI want to know about the diff between soft and softer HO?
3rd March 2006 at 08:56 #42115Kuma
GuestSoft HO is between two cells at different sites. Softer HO is between two co-located (at same site) cells.
3rd March 2006 at 09:03 #42116santy
Guestcan u explain in terms of sector -carrier?
3rd March 2006 at 09:36 #42117Kuma
GuestBoth Softer and Soft HO are within one frequency.
3rd March 2006 at 09:39 #42118Santy
GuestWhat if one cell is 2 FA and other is 3 FA…And if the person on third frequency going to next site having two carriers?
3rd March 2006 at 09:43 #42119nassim
Guestyou have one parameter you need to adjsut in this case
RTD: round trip delayregards
3rd March 2006 at 09:57 #42120Santy
GuestNassim…
Can u elaborate your point?3rd March 2006 at 10:04 #42121nassim
GuestDear Santy
When the mobile’s RTD passes upward through a datafilled threshold,the system steps in and orders a hard handoff to the matching sector of the bridge cell on the other system
regards
Nassim3rd March 2006 at 16:22 #42122Niyi
GuestI have worked on circuit switch but am trying to move into SOFTSWITCH. I mean IP Telecomms engineer. am in Lagos Nigeria.i also need foundamentals of VoIP STUFF.
THANKS
Regards
Niyi5th March 2006 at 07:15 #42123amberish
Guesthi santy, answer to ur question if person going from two carrier to third carrier site then there is no problem. He will get only hard handoff but if he is going from 3 carrier to 2 carrier site then u have to define parameter DAHO in 3c site so customer call will not get dropped when he is moving from 2c to 3c. I hope it will clear ur doubt.
18th April 2006 at 07:18 #42124venkat esh
GuestHi Amberish/Santy,
This is in reference to A mobile moving from 3C to 2c.
let the frequencies with BTS A be F1,F2,F3 & BTS B be F1,F2.
If mobile is moving from A to B there is no problem, but if the mobile is moving from B to A and With The Mobile Hashed to F3. Then Border definitions have to be defined in such a way that F3 is H/O to F2.
rgrds
Venkat19th April 2006 at 06:50 #42125yvravi
GuestHi Nassim/Shanty,
Transalations allow selected sectors to be configured for Inter Frequency Handoff.To Maximize the coverage/Capacity acheived on aborder cell it is recommended that the only outward facing sectors of each Fn/Fi.Border cell be configured for Inter Frequency Handoff.The inward facing sectors will normally configured for Fn Traffic.
-
AuthorPosts
- The forum ‘Telecom Design’ is closed to new topics and replies.