Free Erlang traffic calculators

The world's first online Erlang traffic calculators

Telecom Traffic Online
  Home | Free calculators | Products | Tech. papers | Forum | About us
A-Z termination - click here
A-Z termination - CLICK HERE
A-Z termination using H.323 and SIP
A-Z termination
  • VoIP softswitch

    DUAL Softswitch is a complete Voice over IP switching and billing solution.  Flat monthly rate.

    Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support.

    H323 SIP softswitch >>

  • VoIP calling

    Premium quality termination for wholesale carriers with their own VoIP switch.

    44Direct >>


    Our lowest rates for wholesale carriers with their own VoIP switch.

    44Mobile >>


    Our unique online callshop billing system.

    Bill My Calls >>

incoming ho

Harison - 20th September 2018  (07:28 GMT)

Hi,
I don't understand the Incomming HO and Outgoing HO. Could you to give me their threshold?

pix - 14th June 2011  (16:47 GMT)

hi alexia,

but then, in another cell, you have very poor outgoing and very good incoming % :)
normally, you should consider only the outgoing ho in the HOSR.

regards
pix

Alexia - 14th June 2011  (12:59 GMT)

In calculating HOSR do we consider both incoming and outgoing??

I have some cells with poor incoming but excellent outgoing handover successes.

adi - 8th August 2009  (12:07 GMT)

Hi all,


I have a poroblem in a cell in remote area have bad incomming and out going hanover.
The distance between the nieghbor cells is 35 km antena height=75m
im using erisson equipment TCC feature is activate on this cell.

pls help..

Mouf - 18th February 2009  (13:58 GMT)

Hi all

I solve the problem of incoming ho by deleting and recreating all relations of my cell.

thanks!

TNS - 31st January 2009  (20:05 GMT)

Hi, mouf.

Are you sure parameter RxLev_min(n) is low enough?

May be I should activate General Capture HO towаrd this cell ( just to get some requests )...

BR

Alex_R - 30th January 2009  (08:24 GMT)

Dear mouf

did u check uplink signails of this cell may be link inbalance exist ?

mouf - 27th January 2009  (14:26 GMT)

Hi Pix,

The release is B9.
Thanks.

pix - 27th January 2009  (12:55 GMT)

Hi,

There were similar problems in B8. Two possible actions:
Restart OMU
or change the BSIC (this i'm not sure... perhaps, you should rather try to delete the cell and recreate it from scratch)

If nothing works, then you should raise the issue to your TAC. In which release are you?

mouf - 27th January 2009  (10:49 GMT)

Hi All,

adcguy : response to your question is yes. The cell carried traffic and do outgoing handover .

Pix,

It is a misunderstanding. I mean "a cell facing" not " e cell".
All neighbors belong to the same BSC , one LAC et...
In Incoming, we 've got no HO requests and no HO attempts.
In outgoing everything is OK.
(Alcatel vendor). The cell is not at a border location.

Thanks for any help!!!

Other messages

Other messages: [Next 10 >>]

Post a reply to this article

Name Enter your name.
Message Enter your message.
Email Optional -  If you enter your email address in this box, then you will automatically be notified if anyone replies to your message.  Your email address will only be published if you pay to post this message.
Verification
Please confirm you are human.
Press the button to post your message.
Home | Free online calculators | Products | Technical papers | Forum | Contact us | About us

Last modified: 17 May 2017

Copyright 2017. All rights reserved.