Free Erlang traffic calculators

The world's first online Erlang traffic calculators

Telecom Traffic Online
  Home | Free calculators | Products | Tech. papers | Forum | About us
A-Z termination - click here
A-Z termination - CLICK HERE
VoIP bandwidth calculator
  • VoIP softswitch

    DUAL Softswitch is a complete Voice over IP switching and billing solution.  Flat monthly rate.

    Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support.

    H323 SIP softswitch >>

  • VoIP calling

    Premium quality termination for wholesale carriers with their own VoIP switch.

    44Direct >>


    Our lowest rates for wholesale carriers with their own VoIP switch.

    44Mobile >>


    Our unique online callshop billing system.

    Bill My Calls >>

CRH parameter issue

Samer - 5th September 2017  (07:04 GMT)

thanks, we actually appreciate your help, i will check with my group and return back to you for any new progress. my greetings :)

pix - 30th August 2017  (19:31 GMT)

ok... but exactly, what are you looking at ? can you share some values ?

with a CRH = 14, you should see a huge issue in GPRS mobility (a lot of TBF drops)

you should also see less SDCCH LAU, and a decrease in CSSR, because MS are stuck in their serving cells, without being able to move to (reselect) a better neighbour cell.

With a ACCMIN = 110, the effect should be even more pronounced.

The Ericsson implementation of the CRH is fine, I can see it in the many DT I've done, no worry about that aspect.

Let's do some testings ? select two cells, one from each side of a LAC border.
Put CRH = 0dB on both cells
Put CRO = 10dB on cell A, observe that trafic increases in Cell A
Put CRH = 20dB on cell B, observe that trafic increases (a little) on cell B, and decreases (a little) on cell A. Also, you should not there is less SDCCH LAU in cell A.

Now there is another possibility that the border between cell A and B is very "poor", meaning that RXLEV dips below -110dBm, in which case the MS will not be using the CRH anymore.
CRH works well if RXLEV at borders are "CRH" dB higher than ACCMIN.

Let me know how it goes...

Samer - 30th August 2017  (12:47 GMT)

thank you for your efforts, however we put the default values for the parameters you mentioned as follow:
CRO 0
TO 0
CRH 14
PT 0
T3212 30
ACCMIN 110
CBQ high

we actually tried all possible values to CRH and nothing happened so a conclusion came out that an other parameter might control its behavior or something stuck in Ericsson device !!

pix - 30th August 2017  (12:22 GMT)

hi,

No, nothing special in E///. CRH and CRO are always active.

BTZ - Ensure that CRH is set to a high value in the neighbours of the cell you are observing.
If CRH(neighbours) is high, that will reduce the number of incoming cell reselections in the serving cell.

I can have a look at your settings if you want ? Please list the parameters values :
CRO
TO
CRH
PT
T3212
ACCMIN
CBQ

br / pix

Samer - 30th August 2017  (08:28 GMT)

i am waiting and thanks in advance :)

pix - 29th August 2017  (19:33 GMT)

hi samer,

ok, so in this case I believe, if I remember correctly, that you need to activate the computation of the C2 criterion.
This is controlled by a radio parameter in ALU. But I need to check it out in E///. I'll answer more precisely tomorrow.

br /pix

Samer - 28th August 2017  (10:41 GMT)

thank you. however i am looking if there is any other parameters will control CRH parameter behavior. for example in BTS or BSC or MSC parameters. you need to know that we have 2G network only and 3G not yet implemented.

pix - 28th August 2017  (10:14 GMT)

Hello Samer,

What kind of effect are you looking for ?

You should see a decrease of the number of 2G LAU on cells located at lac borders.
However, it might be difficult to see it... because there is still many 2G LAU due to 3G to 2G mobility (at the end of a call with IRAT HO , or Idle mode 3G-2G). So you shouldn't expect such a huge impact of CRH on the number of 2G LAU. On top of that, CRH will reduce the pingpong 2G LAU, but many MS are really moving from LAC to LAC (physical mobility along highways, roads, rails...), in which case the CRH will only delay the inevitable LAU.


To reduce the 3G2G mobility,
- activate the "fast reselection",
- inhibit the IRAT HO,
- decrease the qRxlevmin (from -112dBm to -114dBm for example)

Cheers,

pix

Samer - 27th August 2017  (13:59 GMT)

hello, i have problem with CRH parameter assignment. is there any other parameters will affect its behavior maybe not only in RBS but on BSC or MSC. although CRH value have been changed no effect is happened please give me any hint. we use Ericsson hardware.

Post a reply to this article

Name Enter your name.
Message Enter your message.
Email Optional -  If you enter your email address in this box, then you will automatically be notified if anyone replies to your message.  Your email address will only be published if you pay to post this message.
Verification
Please confirm you are human.
Press the button to post your message.
Home | Free online calculators | Products | Technical papers | Forum | Contact us | About us

Last modified: 17 May 2017

Copyright 2017. All rights reserved.