Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

d2400 call relay problem

Viewing 3 posts - 1 through 3 (of 3 total)
  • Author
    Posts
  • #31574
    mastaplan
    Guest

    Hello,

    Im configuring tenor d2400 on 1 e1 connection on asterisk server.

    I successfully configured the outbound routes. (I can call from my ATA phone then goes out to the e1 connection).

    My problem is i can’t able to pass the incoming calls coming from my e1 to the sip server.

    Can anybody help me out on configuring this?

    i tried to get the logs on ev log and im getting an alarm on ev log “bad ip str”..

    #31575
    MikeM to Mastaplan
    Guest

    If you are using SIP, you need to make sure you have the sip server configured in the quintum and that all incoming calls have a destination number. At that point the quintum will send a message to the sip server for routing instructions.

    MikeM
    mike_voip@hotmail.com

    #31576
    Mastaplan
    Guest

    Thanks for the reply.

    I have configured my sip primary registrar and proxy in the quintum.

    when i checked the sip stat command in the CLI it says registered.

    Im debugging my quintum and the alarm shows:

    CH : 25043553:Received ANI: 09228757478.
    CH : 25043553:received info = 0973777111F
    CH : 25043553:[2:27] sent message to cas: Call-Proc
    CH : 25043553:Routing requested for: public(1) orig=0973777111F public(1) normalized=0973777111 route code= tg=0.
    CH : 25043553:1 match(es) found: 2
    CH : 25043553:chsip : bandwidth info: max=-1 cur=12600.
    CH : 25043553:Route response(154): result=1 cause=0.
    CH : 25043553:TBCSM[154]: Setup from peer=0xd08004 NP=0x1 NT=0x1.
    CH : 25043553:OrigNum=0973777111F NormNum=0973777111 TranNum=0973777111 OrigDest=.
    CH : 25043553:sip[154]: tsipcall:stackSendSetup, media type=16
    CH : 25043553:udp connect: 2 11
    CH : 25043553: cba763b7 10240 0 0
    CH : 25043553:siptg: outgoing translation 0973777111F -> 639730973777111.
    CH : 25043553:sent message to sip: msg=2; ua=1
    EXCP : 25043561:Bad IP addr str= calling proc=0x498ba0 proc1=0x470bac
    EXCP : 25043569:Bad IP addr str= calling proc=0x498ba0 proc1=0x470bac
    CH : 25043573:sip[0/0]: SipReleaseComplete rcvd at SipTermCall
    CH : 25043573:sip[154/0]: tsipcall:RcvRelComp, cause=111
    CH : 25043573:udp disconnect: 2 11
    CH : 25043573: cba763b7 10240 0 0
    CH : 25043573:OBCSM[154]: Release from peer=0xd0680c cause=0x6f redir=.
    CH : 25043573:TBCSM[154]: Release complete from peer=0xd08004.
    CH : 25043573:sip[0/0]: sipTG::term releaseCall:remove call from list

    how do you configure this?

    TIA

Viewing 3 posts - 1 through 3 (of 3 total)
  • The forum ‘Voice over IP’ is closed to new topics and replies.