Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Ring Back Tone Problem

Viewing 6 posts - 1 through 6 (of 6 total)
  • Author
    Posts
  • #31567
    Hasan
    Guest

    I cannot hear ringback tone using gnugk 2.2.4, using DSL line. If I use Static Ip that problem not occures. I also changed some portion of gatekeeper.ini file.
    But Problem remain same.

    [RoutedMode]
    GKRouted=1
    H245Routed=1
    CallSignalPort=1721
    AcceptNeighborsCalls=1
    AcceptUnregisteredCalls=1
    RemoveH245AddressOnTunneling=1
    RemoveCallOnDRQ=1
    DropCallsByReleaseComplete=1
    SendReleaseCompleteOnDRQ=1
    SupportNATedEndpoints=1
    ForwardOnFacility=1
    ShowForwarderNumber=1
    Q931PortRange=10000-10999
    H245PortRange=30000-30999
    ConnectTimeout=90000
    ActivateFailover=1
    FailoverCauses=1-15,21-127

    [Proxy]
    Enable=1
    T120PortRange=40000-40999
    RTPPortRange=50000-50999

    Please prompt me soon

    #31568
    Eric11190
    Guest

    You can try to capture the RTP at your end site after the 183 or 180 message. if there is RTP flow in, that’s mean the RBT should be working. If you can not get the RBT, then there is the endpoint issue.
    For the EyeBeam, the version t3004 can not get the RBT. But the version t3010 can get the RBT.

    #31569
    Hasan
    Guest

    I am using quintum AX. If i set answer delay 0 then false ringtone generated due to the ad value. But it
    shows call connected at dialer, just
    after dialing the digit.

    So Setting answer delay to 0, doesn’t
    also works.

    If you have other suggestions, plz prompt me.

    #31570
    MikeM to Hasan
    Guest

    Not sure exactly what you are trying to do, but if you are looking for correct answer supervision, you would set answer delay to 90 or more along with the other supervision parameters as documented in the answer supervision document on quintum’s web site.

    As for the false ring tone, without seeing the config, I cannot say for sure, but 80% of the time, it is the origination device that is providing the false ring tone.

    MikeM
    mike_voip@hotmail.com

    #31571
    tarik
    Guest

    I have a pb with FAS (False Answer Supervision) on a Quintum. How can i do to solve it please?

    #31572
    Gias
    Guest

    I am faching peculiar problem with my Tenor AX.. Today I have just downgrade my Tenor AX.. And after that I can’t enter my gateway.. There are somw error mssege geting from my GW.. as like belows.. And I am not getting any loging prompt too.. Plzz help me..

    Loading boot software…Version P100-21-00

    +————————————————————————–+
    | TENOR SOFTWARE |
    | |
    | (C) Copyright 1998-2004 Quintum Technologies Inc. All Rights Reserved. |
    | |
    | Hardware Revision: Unknown0110
    | |
    +————————————————————————–+

    Loading software: Length = 3328645, Checksum = 0x4f56. Please wait…

    Attaching network interface lo0… done.
    0x97369070 (tNetTask): Link is down on LAN 1

    VxWorks

    Copyright 1984-2001 Wind River Systems, Inc.

    VxWorks: VxWorks5.4.2
    Created: Mar 18 2005, 12:29:52

    *******************************************************
    WARNING: Tenor does not contain a valid license file.
    Operating in reduced functionality mode.
    *******************************************************

    Initializing Database…
    Loading database ………………………………
    Loading Help…
    Loading Messages…
    Done.

Viewing 6 posts - 1 through 6 (of 6 total)
  • The forum ‘Voice over IP’ is closed to new topics and replies.