Generic selectors
Exact matches only
Search in title
Search in content

we can help any kinds of quintum config

Viewing 15 posts - 61 through 75 (of 109 total)
  • Author
    Posts
  • #28879 Reply
    vamsi
    Guest

    hi any body help to reset
    the password for quintum Ax series
    gatewasy.
    Any one plz mail me .. urgent

    #28880 Reply
    MikeM to vamsi
    Guest

    Vamsi,

    I tried to provide you specific info to do this, yet this wonderful posting area will not allow certain words (unknown which ones) to be used and I cannot post the exact resolution. You can search through the messages on this topic as it has been discussed many times

    Mike

    #28881 Reply
    Taisisgüe
    Guest

    Hello, ?
    I need delete a config in my Quintum AX series.
    BypassNumberDirAttached[1] : (unspecified)
    BypassNumberDirAttached[2] : BypassNumberDirectory-1
    BypassNumberDirAttached[3..8]: (unspecified)
    PUBHuntLdnDirAttached[1] : HuntLDNDirectory-pub2

    I need delete the BypassNumberDirAttached[2] : BypassNumberDirectory-1
    What is the command for do this I configured but cannt dellete it.

    can you help me please…

    #28882 Reply
    MikeM to Taisisgüe
    Guest

    Taisisgüe

    In the future, you should download the Command Line reference guide from quintum’s web site under the support section as this should provide you the information needed.

    To remove this you need to type

    set bnda[2]

    Of course you need to be in config mode.

    MikeM
    mike_voip@hotmail.com

    #28883 Reply
    Taisisgüe
    Guest

    Thanks So much Mike.
    I have the file with the commands CL of Quintum but I cannt found it,
    Sorry for spend your time with little problem.
    thank you very much.
    Have a great day
    Regards.

    #28884 Reply
    raj
    Guest

    i have quin axt2400. my ISP block 1720 port.i want to run it diffrent port like 8022 or 8920.

    #28885 Reply
    syedrepon
    Guest

    please help me i want any for quintum ax & other configuration software.my email:syedrepon@yahoo.com

    #28886 Reply
    MikeM to syedrepon
    Guest

    Not sure what you are asking, but if you are looking for software for the quintum units, you should try quintum’s web site first as all the software and documentation available can be found there.

    MikeM
    mike_voip@hotmail.com

    #28887 Reply
    prabesh kc (nepal)
    Guest

    Dear frens,
    I’m using quintum tenor A800. One of my fren disable web configuration. Plz help me to enable remote web configuration.
    thanks in advance.
    Regards,
    Prabesh

    #28888 Reply
    MikeM to prabesh
    Guest

    Prabesh,

    If you have an older A800, it is not a case that your friend has disabled it, it is just not available in the older units like A800. You can only configure using telnet.

    MikeM
    mike_voip@hotmail.com

    #28889 Reply
    prabesh kc (nepal)
    Guest

    Thank you So much Mike.
    I’m using Quintum Tenor Multipath switch with serial A002-002F4D/A800. Previously I can able to configure via web interface but nowadays one of my friend disable web configuration or I’m not able to access via internet explorer. Only telnet access work. My friend is out of contact. Now I need to open/close pstn channels and it is easy with web cofiguration. So, Please..please….please help me to enable web configuration or command to open/close channels.
    Thanks in advance.
    Regards,
    Prabesh K.C.
    Kathmandu, Nepal.

    #28890 Reply
    MikeM to prabesh
    Guest

    Prabesh,

    There are 2 issues here.

    1. I believe that due to the size of the latest software, the web interface was completely removed/disabled.

    2. Even before that, if you used the web interface in the A800 before and you did not have problems. Consider yourself very lucky as the web interface has not really worked correctly since the beginning.

    You should start using and getting used to telnet/cli as this is the only way to really configure the A800.

    If you want to disable/enable channels in the pstn port, you do the following from telnet;

    config pstn 1
    dis 1 x (where x = channel number or a for all)
    or
    ena 1 x (where x = channel number or a for all)
    print (to check your setting)
    exit
    exit
    submit

    MikeM
    mike_voip@hotmail.com

    #28891 Reply
    Inspire
    Guest

    Hi,

    I have Quintum Tenor DX
    I have 2 PRI on my Quintum and have 200 DID number..

    When Somebody calls me dial 123 and extension
    Like 123 5511
    But when I dial someone to outside they can not see 123 5511 !!!
    They see 123 0000 which is my PRI number.

    How can I configure my quintum to correct this problem…

    #28892 Reply
    MikeM to Inspire
    Guest

    There is a setting for default ANI in the isdn signaling group. Whatever value you set here will be sent out as the ANI.

    MikeM
    mike_voip@hotmail.com

    #28893 Reply
    Inspire
    Guest

    Let say my phone number is 1155
    and my Caller ID send as 1155
    I want to add 0392611 prefix before 1155
    like 03926111155

Viewing 15 posts - 61 through 75 (of 109 total)
Reply To: Reply #28835 in we can help any kinds of quintum config
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">