- This topic has 1 reply, 1 voice, and was last updated 15 years, 5 months ago by I have the same thing.
-
AuthorPosts
-
1st August 2004 at 17:33 #27723CT HungGuest
Dear all,
I have a AS5300 with 1*4 channelized E1 card,and 1*DSPM model (30dsps,60 channedls).
Question: When I issue “show voice port 0:15”,it shows no DS0 message.There should be 60 channels(DS0).
I am sure the VFC card is installed with 30 dsps.
—————————–
AS5300 connects to Nortel PBX:
-isdn switch-type primary-net5
-voice service voip
h323
-controller E1 0
framing NO-CRC4
clock source line primary
pri-group timeslots 1-31
!
-interface Serial0:15
no ip address
isdn switch-type primary-net5
——————————
ISDN 0:D – 0:D
Type of VoicePort is ISDN
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 8 ms
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 200 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is A-law
Region Tone is set for US
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):DS0 channel specific status info:
IN OUT
PORT CH SIG-TYPE OPER STATUS STATUS TIP RINGas5300#
as5300#show vfc 2 board
VFC board state is UP, vfc status VCWARE running(0x4)
VFC board in slot 2 with 30 dsps
as5300#>>
>>Does anybody can kindly help?Thanks.
C.T.
4th July 2009 at 17:22 #27724I have the same thingGuestIt seems the firmware on this things is a little buggy, and different versions (which I have) don’t match the documentation – in some cases (like faxing) (or the incoming voice modem command) directly contradict the documentation and I’ve spend at *LEAST MANY* tens of hours making changes – because there doesn’t seem to be to much useful information – just quotes to the Cisco doc’s which are plain old wrong, for the As5300 because the group it with other products like the 5350, and 54XX. (don’t mind the email it’s for hopefully soon, my wife, it’s the only one I check often) … but … if your still having problems I can help you with ANY thing you need with the Cisco, Asterisk, SIP and integrations via PRI’s (or god forbid T1’s) to ‘legacy’ like a Nortel MICS . It actually works *MUCH BETTER* then the Cisco rip everything out and replace everything with software, their phones and scrap the current investment – then only to trust your enterprise with a call manager running on *FREAKING WINDOWS* !
Can’t help you with CCM though – I used it a bit when I was forced to by the custom until I talked them into converting to Asterisk – then all problems where gone and *MUCH BETTER PERFORMANCE*. Although Asterisk does have it’s problems acting as a LARGE SIP gateway with thousands of connections being invited, and much less if the call has to be bridged because of NAT
-
AuthorPosts
- The forum ‘Voice over IP’ is closed to new topics and replies.