Generic selectors
Exact matches only
Search in title
Search in content

Help needed Quintum A400

Viewing 3 posts - 1 through 3 (of 3 total)
  • Author
    Posts
  • #26295 Reply
    Essam
    Guest

    The tenor is connected to a linksys router which is connected to an ADSL modem (alcated speedtouch) which is acting a bridge only.

    A phone jack is connected to a PBX port. When we pick up the phone, we get no call Tone, and after 5 seconds we get a busy tone.

    Here is the log:
    CH : 25282056:[1: 1] received message from cas: RelComp
    CH : 25282056:tsi disconnect: 101 208 10
    CH : 25282056:TsiDiscXlate: 2:8, 1:1
    CH : 25282336:[1: 1] received message from cas: Setup
    CH : 25282336:CallInfo[0xd8c828]: origCalled.digit()
    .
    CH : 25282336:[1: 1] sent message to cas: Call-Proc
    CH : 25282336:Routing requested for: public(1) orig= public(0) normalized= route code= tg=0.
    CH : 25282336:2 match(es) found: 1 5
    CH : 25282336:bandwidth info: max=-1 cur=12600.
    CH : 25282336:Route response(49): result=1 cause=0.
    CH : 25282336:TBCSM[49]: Setup from peer=0xd8c804 NP=0x0 NT=0x0.
    CH : 25282336:OrigNum= NormNum=723# TranNum=723# OrigDest=.
    CH : 25282337:h323[49]: tcall:stackSendSetup, media type=9
    CH : 25282337:udp connect: 1 11
    CH : 25282337: c0a80165 10240 0 0
    CH : 25282337:tcall: trying route to 216.52.153.206.
    CH : 25282337:h323[0]: h323mgr:newCall
    CH : 25282338:[1: 1] received message from cas: InbandSigDone
    CH : 25282767:h323[49/0]: tcall:RcvRelComp, cause=38 reason=0.
    CH : 25282767:udp disconnect: 1 11
    CH : 25282767: c0a80165 10240 0 0
    CH : 25282767:OBCSM[49]: Release from peer=0xd8b010 cause=0x26 redir=.
    CH : 25282767:TBCSM[49]: Release complete from peer=0xd8c804.
    CH : 25282767:OBCSM[49]: Trying another route.
    CH : 25282767:Route response(49): result=0 cause=34.
    CH : 25282767:CallInfo[0xd8c828]: cdr callid(31) rmtcallid(0) calltype(1) destnumtype(0).
    CH : 25282767:CallInfo[0xd8c828]: cdr dest(723#) orig(329602036085 12) remote() pin().
    CH : 25282767:CallInfo[0xd8c828]: cdr icline(0) icport(0) otline(ffffffff) otport(0).
    CH : 25282767:CdrManager::addCdr: 48 Return.
    CH : 25282767:tsi connect: 101 209 10
    CH : 25282767:TsiConnXlate: 2:9, 1:1
    CH : 25282767:[1: 1] sent message to cas: Alert
    CH : 25283030:[1: 1] received message from cas: RelComp
    CH : 25283030:tsi disconnect: 101 209 10
    CH : 25283030:TsiDiscXlate: 2:9, 1:1
    CH : 25289042:h323mgr:GateKeeper Found

    I cannot figure out what the problem is.

    #26296 Reply
    Noname
    Guest

    I am very curius about what you have setup on your Quintum.

    Specifically on the PBXTG section. Looks like you have the PBX ports “hotlined” to a I.P. address somehow.

    Go to the prompt, type config, and then “print”.

    If you want, mask the first octectof the I.P. addresses, post the result or send then to me to mike3799@yahoo.

    I will be able to send you the text file with the corrections to make calls.

    Good luck!!!!

    #26297 Reply
    Essam
    Guest

    Here is a copy of the config

    Unit
    —-
    Unit: 1
    IP Address = 192.168.1.101
    External IP Address = 0.0.0.0
    Name = voip

    Online = 1
    Relay ResetTime = 240
    Relay Reset Number = 2

    TcpKeepAlive = Enabled(1)

    System
    ——
    Country Value = 4
    Country Code =
    Area Code =
    Minimum DN = 3
    Maximum DN = 20
    International Prefix:
    Long Distance Prefix = 0
    Carrier Selection Prefix:
    Intercom Used = no(0)
    Private DN Used = no(0)
    Interdigit Timeout = 4 sec.

    Contact =
    Location =
    IP Address : of Snmp Trap Server 1 = 0.0.0.0
    IP Address : of Snmp Trap Server 2 = 0.0.0.0
    IP Address : of Snmp Trap Server 3 = 0.0.0.0

    IP Address : Port # of Syslog Server 1 = 0.0.0.0 : 514
    IP Address : Port # of Syslog Server 2 = 0.0.0.0 : 514
    IP Address : Port # of Syslog Server 3 = 0.0.0.0 : 514
    Syslog Facility = 16

    IP Address : Port # of Cdr Server 1 = 0.0.0.0 : 0
    IP Address : Port # of Cdr Server 2 = 0.0.0.0 : 0
    Cdr Password:
    Cdr Format: 0

    Ring Frequency = 20 Hz(0)
    PSTN Ring Sensitivity = Normal(0)

    Primary Time Server: IP Address = 0.0.0.0
    Secondary Time Server: IP Address = 0.0.0.0
    UTC Offset: Unknown

    Disc Tone Frequency: 480 Hz (min) : 620 Hz (max)
    Disconnect On/Off Time: 250 mSec(on) : 250 mSec(off)

    Call Indication Tone = None(0)
    Disable GUI = no(0)

    Dialplan
    ——–
    User Programmable DP = No
    Dialplan table:
    index:Pattern DpType min max nprefix

    System LAN
    ———-
    Subnet Mask = 255.255.255.0
    Default Gateway = 192.168.1.1

    PSTN Trunk Group
    —————-
    PSTN Trunk Group: 1
    Name = PstnPassThrough1
    Pass Through = no(0)
    PT Trunk ID = 0
    Provide Call Progress Tone = no(0)
    Busyout = no(0)
    Hunt Algorithm = ascending(0)
    Modem Calls = No(0)
    Direction = both(2)
    DN Used = public
    End Of Dial = yes(1)
    End Of Dial Digit = #
    Add End of Dial Digit = no(0)
    Ivr Type = None
    CID = From Interface(0)
    External Routing Request = no(0)
    Auto Switch Enable = no(0)
    Forced IP Routing # = none
    Trunk ID(Account Code) = none
    Trunk ID Delivery = none
    2 Stage Dial = No
    Translate Inbound Caller ID = no(0)
    Relay Caller ID = yes(1)
    IP Extension = yes(1)
    channel ip-addr dnis rmt-line chan
    channel *: 216.52.153.206 723#
    Maximum LAM Calls Allowed = 4
    LAM: Index Pattern Replacement NumberType
    Cas Signaling Type = loop start(1)
    Cas Orientation = user(0)
    Dial Tone Detect = yes(1)
    Dial Delay Timeout = 1000
    Answer Delay Timeout = 0
    Flash-Hook Signaling = no(0)
    Supervision = none(0)
    Caller Id Detection = no(0)
    dtmf-ontime = 100
    dtmf-offtime = 100
    Channel:
    unit# 1 line# 2: 1,2,3,4

    PBX Trunk Group
    —————
    PBX Trunk Group: 1
    Name = PbxPassThrough1
    Pass Through = yes(1)
    PT Trunk ID = 0
    Provide Call Progress Tone = no(0)
    Multipath = no(0)
    Hunt Algorithm = ascending(0)
    Modem Calls = No(0)
    Direction = both(2)
    DN Used = public
    End Of Dial = yes(1)
    End Of Dial Digit = #
    Add End of Dial Digit = no(0)
    Ivr Type = None
    Partial TG = no(0)
    CID = Trunk ID(1)
    External Routing Request = no(0)
    Auto Switch Enable = no(0)
    Forced IP Routing # = none
    Trunk ID(Account Code) = none
    Trunk ID Delivery = none
    2 Stage Dial = No
    Translate Inbound Caller ID = no(0)
    Relay Caller ID = yes(1)
    IP Extension = yes(1)
    channel ip-addr dnis rmt-line chan
    channel *: 216.52.153.206 723#
    Public Number of Digits = 7
    Private Number of Digits = 7
    Public Hunt Ldn’s:
    1: 329602336085
    Private Hunt Ldn’s:
    BDN: Index Bdn
    Cas Signaling Type = loop start(1)
    Cas Orientation = net(2)
    Flash-Hook Signaling = yes(1)
    Flash-Hook Min = 200
    Flash-Hook Max = 700
    Supervision = none(0)
    Caller Id Generation = no(0)
    dtmf-ontime = 100
    dtmf-offtime = 100
    Channel:
    unit# 1 line# 1: 1,2,3,4

    IP Trunk Group
    —————
    Incoming IP call delete digits = 0
    Incoming IP call prefix =
    Outgoing IP call delete digits = 0
    Outgoing IP call prefix =
    Prefix Trunk ID = no(0)
    Default Trunk = No
    External Routing Request = no(0)
    Display Information ID = Tenor-Gateway

    Line
    —-
    Line: 1
    Law = uLaw(0)
    Rx Gain = -4dB
    Tx Gain = -2dB
    Line: 2
    Law = uLaw(0)
    Rx Gain = 0dB
    Tx Gain = 0dB
    Guard Time = 0mS
    DAA Start Up = Enabled

    Bandwidth Management
    ——————–
    Time of Day Maximum Bandwidth:
    Day = 0(Sunday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 1(Monday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 2(Tuesday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 3(Wednesday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 4(Thursday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 5(Friday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 6(Saturday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *

    Gatekeeper Administration
    ————————-

    Endpoint Authorization Type = 0 (None)

    Allowed Endpoints
    IP Mask
    No Allowed Endpoints Configured

    Barred Endpoints
    IP Mask
    No Barred Endpoints Configured

    Gatekeeper System
    —————–
    Zone Name = saudi
    Border Element IP Address(prim) = 0.0.0.0
    Border Element IP Address(sec) = 0.0.0.0
    Discovery IP Address = 0.0.0.0
    Gatekeeper Password =
    LRQ returns all candidates(0)
    Maximum LRQ Hops = 0
    WAN Call Limit = 0 (disabled)
    LCF/LRJ V3plus = 1
    Gatekeeper Option Flags:
    Use IP Header Address = no(0)
    Ridgeway ARQ = no(0)

    Border Element
    —————–
    Static Routing
    No Static Routes configured

    DSP

    Voice Coding algorithm = 81
    Voice Information Field size = 192 bits
    Silence Suppression = Enable(1)
    Minimum Jitter buffer = 60 msec
    Maximum Jitter buffer = 300 msec
    Receive Gain (PCM -> IP) = -2 dB
    Transmit Gain (IP -> PCM) = -4 dB
    Digit Relay = 0
    Fax Relay Type = 0
    Fax Maximum Rate = 144
    Fax Playout FIFO nominal delay = 600
    Fax Modem Coding = 0
    Idle Time = 0
    Answer Supervision Options = 0

    AutoSwitch
    ———-
    Auto Threshold = 50

    H323 Gateway
    —————–
    Primary GK Address = 0.0.0.0
    Primary Auto Discovery = 1
    Secondary GK Address = 0.0.0.0
    Secondary Auto Discovery = 0
    H.323 ID = remal
    Register DN = Register as E.164 IDs(2)
    Ignore Bandwidth in ACF = no(0)
    Default H245 Tunneling = yes(1)
    Round Trip Delay = 0
    One Stage Dialing = 0
    RRQ Interval = 0
    H323 Interop Flags:
    H225 GW Protocol = h323(0)
    Do BRQ = 0
    SlaveSessionId0 = 0
    AllowFastStartOnly = No(0)
    RRQv3plus= No(0)
    ProgressInd Alert= No(0)
    StartH245Flag= No(0)
    Automatic Ext IP Update= No(0)
    RTP Verification= No(0)

    Do Lightweight RRQ = no(0)

    Radius User
    ———–

    host p 0.0.0.0
    authenticationport p 1812
    accountingport p 1813

    host s 0.0.0.0
    authenticationport s 1812
    accountingport s 1813

    retry = 3
    timeout = 5
    accountingtype = 0
    billingvendor 0
    sharedsecret

    IVR
    ——

    Primary File Server: IP Address = 0.0.0.0
    Secondary File Server: IP Address = 0.0.0.0
    timeout: 5

    Enabled Languages: None

    CID Translation Table
    ——
    Caller ID Translation Table
    Index Pattern Replacement

    Radius Endpoint
    —————

    host p 0.0.0.0
    authenticationport p 1812
    accountingport p 1813

    host s 0.0.0.0
    authenticationport s 1812
    accountingport s 1813

    retry = 3
    timeout = 5
    idtype = 0
    passwordtype = 0
    sharedsecret

    Product Name: Tenor Analog A400 Multipath Switch – 4 ports (Rev. B)
    Gatekeeper Status: Mini
    GK Calls Allowed: 4
    Feature Bit Status: -PS/+RB/+ER
    Languages allowed: 1
    Serial Number: A002-008771
    Ethernet Address: 00-30-E1-00-87-71
    IP Address: 192.168.1.101
    Subnet Mask: 255.255.255.0
    Default Gateway: 192.168.1.1
    System Software Version: P4-2-20-26(LEC) (1719133/0x66A4)
    Boot Software Version: P4-1-3 (180592/0xE814)
    Database Version: 2.08 09-13-2000 (277900)

Viewing 3 posts - 1 through 3 (of 3 total)
Reply To: Help needed Quintum A400
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">