Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Your opinion about Quintum?

Viewing 15 posts - 166 through 180 (of 287 total)
  • Author
    Posts
  • #23832
    Simo
    Guest

    As I answered in your other question in an equally un-related topic thread, you can easily find this information on Quintum’s web site by reviewing the product specification sheets.

    In short the ASM has 4 fxo and 4 fxs ports. The AXM starts with 8 FXO and 8 FXS ports.

    #23833
    Eno O
    Guest

    Please I need to access my Quintum but I don’t know the original password before accessing it. Please if you have any idea, kindly email it to me. enochok@gmail.com

    Thank you very much

    #23834
    Max
    Guest

    What equipment is needed to to provide calling cards service. Can this be done with a intergrated Cisco or Quintum unit.

    #23835
    Teodor Georgiev
    Guest

    Guys, do not buy the FXO-equipped second generation Quintums.
    They are still unreliable.
    Their disconnect supervision algorithm is crappy.
    You will fall into a trouble.

    #23836
    Zaman
    Guest

    Hello guys,

    I need to learn Quintum A800 and AX800 configaration,Can any one help me? I cometment I will do something for him.

    #23837
    ngozi braide
    Guest

    we have used the configuration you sent, using our own ip addresses, but what of the call signal IP address,
    what IP address SHOULD IT BE, YOURS
    OR OURS.

    #23838
    DJEUYA
    Guest

    please i need documentation to install and setup my quintum A400

    #23839
    MikeM
    Guest

    DJEUYA,

    did you try looking at Quintums web site under the support area?

    #23840
    Wilson Boyrie
    Guest

    On http://WWW.quintum.com, on the bottom of the page, click on customer service, you will have all the manuals and information about the Quintum.

    #23841
    Zaman
    Guest

    I think i can help you with your problem… i will expalin to you on the configurations

    #23842
    Jack
    Guest

    “Quintum good all you people here bad” don’t give specific information. If don’t want to give information in details don’t write here.Thank you.

    #23843
    bertcamroy
    Guest

    Hello Zaman i can help you explain configurations… email me at gilbertrumku@yahoo.com maybe i can help you..

    what is your problem Jack?….

    #23844
    Rusty
    Guest

    The latest Cisco IP-to-IP Gateway does SIP H323 and transcoding. It works as a SIP & H323 proxy softswitch and runs on several standard Cisco routers 1850, 2651xm, 3845, and others. Heck you probably have one of these routers all ready in stock. If you have any questions email me monitrader@att.net

    #23845
    riyfat
    Guest

    I have a Quintum Tenor A800 +8 pstn line.Is it possible to run
    multiple dial plan on a single Ip?
    like :
    I want 2 run 4 local call & 4 pstn call on a single Ip. Is there any way to do it ?
    Plz send me some basic

    _callblocking commands
    _call routing commands
    _Ip config command
    _pstn port test command

    It will help me a lot if any one send me thease infos at_
    riyfat@yahoo.com
    riyfat@hotmail.com

    Thanking you.

    #23846
    Surendra
    Guest

    can someone help me to configure quintum A800 with cisco gateway?

Viewing 15 posts - 166 through 180 (of 287 total)
  • The forum ‘Voice over IP’ is closed to new topics and replies.