Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Quintum 800

Viewing 15 posts - 46 through 60 (of 205 total)
  • Author
    Posts
  • #23000
    Noname
    Guest

    There are the same number of phisical ports on the A400 and A800.

    On the A400, they are single ports, with only one phone line per plug.

    On the A800, each plug have two phone lines . One is carried out on the green/red wires, the second line is carried out on the yellow/black pair.

    Take the line that come out from the Quintum to a Rj-11 block. Connect via wires to two diferent phone lines that way.

    Or buy one of those plastic splitters on any electronic stores that open up the lines in two diferent circuits.

    #23001
    Chidi
    Guest

    My Quintum A800 RJ-11 supplied connectors have on one end:single connector and on the other end two connectors labelled ‘A’ and ‘B’. Where do these connect to? Does the PBX connection differ from the PSTN connection? Please help.

    #23002
    Saul Bejarano
    Guest

    Configuration of a Quintum D2400 with voicemaster for IVR.
    For questions contact saul@procomm100.com
    http://www.procomm100.com

    print

    Unit
    —-
    Unit: 1
    IP Address = 65.33.45.234
    External IP Address = 0.0.0.0
    Name = gw.01.usa
    Clock Source = PSTN(0)

    Online = 1
    Relay ResetTime = 240
    Relay Reset Number = 2

    TcpKeepAlive = Disabled(0)

    System
    ——
    Country Value = 0
    Country Code = 1
    Area Code = 239
    Minimum DN = 7
    Maximum DN = 18
    International Prefix:
    Long Distance Prefix =
    Carrier Selection Prefix:
    1: 101xxxx
    US 10 Digit Dial Plan = no(0)
    Intercom Used = no(0)
    Private DN Used = no(0)
    Interdigit Timeout = 4 sec.

    Contact = roger_bruun
    Location = naples-florida
    IP Address : of Snmp Trap Server 1 = 66.250.220.60
    IP Address : of Snmp Trap Server 2 = 0.0.0.0
    IP Address : of Snmp Trap Server 3 = 0.0.0.0

    IP Address : Port # of Syslog Server 1 = 66.250.220.60 : 514
    IP Address : Port # of Syslog Server 2 = 0.0.0.0 : 514
    IP Address : Port # of Syslog Server 3 = 0.0.0.0 : 514
    Syslog Facility = 16

    IP Address : Port # of Cdr Server 1 = 0.0.0.0 : 0
    IP Address : Port # of Cdr Server 2 = 0.0.0.0 : 0
    Cdr Password:
    Cdr Format: 0

    Primary Time Server: IP Address = 128.227.205.3
    Secondary Time Server: IP Address = 216.133.140.77
    UTC Offset: – 05:00

    Disc Tone Frequency: 0 Hz (min) : 0 Hz (max)
    Disconnect On/Off Time: 0 mSec(on) : 0 mSec(off)

    Call Indication Tone = None(0)
    Disable GUI = no(0)

    Dialplan
    ——–
    User Programmable DP = No
    Dialplan table:
    index:Pattern DpType min max nprefix

    System LAN
    ———-
    Subnet Mask = 255.255.255.0
    Default Gateway = 65.33.45.1

    PSTN Trunk Group
    —————-
    PSTN Trunk Group: 1
    Name = ICE_PSTN
    Pass Through = no(0)
    PT Trunk ID = 100
    Provide Call Progress Tone = yes(1)
    Busyout = no(0)
    Hunt Algorithm = ascending-round-robin(2)
    Overlap Dial = no(0)
    Modem Calls = No(0)
    Direction = both(2)
    DN Used = public
    End Of Dial = no(0)
    Ivr Type = Prepaid calling card
    Ivr Card Digit Length = Variables
    Disabled Voice Prompt 0
    Ivr Language Type = 0
    Ivr Language = None
    MultiSession code: = None
    IVR Access Number = None
    Ivr Answer Delay = 4
    Retry Counter = 1
    CID = From Interface(0)
    External Routing Request = no(0)
    Auto Switch Enable = no(0)
    Forced IP Routing # = none
    Trunk ID(Account Code) = none
    Trunk ID Delivery = none
    2 Stage Dial = No
    Translate Inbound Caller ID = no(0)
    Relay Caller ID = no(0)
    IP Extension = no(0)
    Maximum LAM Calls Allowed = 24
    LAM: Index Pattern Replacement NumberType TON NPI
    CCS Or CAS = ccs(0)
    Channel:
    unit# 1 line# 2: 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24

    PBX Trunk Group
    —————

    IP Trunk Group
    —————
    Incoming IP call delete digits = 0
    Incoming IP call prefix =
    Outgoing IP call delete digits = 0
    Outgoing IP call prefix =
    Prefix Trunk ID = no(0)
    Default Trunk = No
    External Routing Request = no(0)
    Display Information ID =

    Line
    —-
    Line: 1
    Law = uLaw(0)
    T1 or E1 = T1(0)
    Line Code = B8ZS(0)
    CRC = yes(1)
    T1 Framing Format = ESF(1)
    T1 Long or Short = short haul(0)
    T1 Length = 133ft(0)
    Line: 2
    Law = uLaw(0)
    T1 or E1 = T1(0)
    Line Code = B8ZS(0)
    CRC = yes(1)
    T1 Framing Format = ESF(1)
    T1 Long or Short = short haul(0)
    T1 Length = 133ft(0)

    Signaling
    ———
    Signaling Group: 2
    Name = cc1
    ISDN Protocol Type = NI2(3)
    Orientation = user/slave(0)
    DCh Num = 24
    Ignore TON/NPI = yes
    FAS unit = 1
    FAS line = 2
    link establishment = always(1)
    Relay PROG = yes(1)
    Force Outbound BCAP = No(0)
    Forced ProgInd IE Outbound = Disabled

    Bandwidth Management
    ——————–
    Time of Day Maximum Bandwidth:
    Day = 0(Sunday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 1(Monday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 2(Tuesday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 3(Wednesday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 4(Thursday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 5(Friday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *
    Day = 6(Saturday)
    Hour = 00 * * * * * *
    Hour = 06 * * * * * *
    Hour = 12 * * * * * *
    Hour = 18 * * * * * *

    Gatekeeper Administration
    ————————-

    Endpoint Authorization Type = 0 (None)

    Allowed Endpoints
    IP Mask
    No Allowed Endpoints Configured

    Barred Endpoints
    IP Mask
    No Barred Endpoints Configured

    Gatekeeper System
    —————–
    Zone Name = naples
    Border Element IP Address(prim) = 65.33.45.234
    Border Element IP Address(sec) = 0.0.0.0
    Discovery IP Address = 65.10.2.209
    Gatekeeper Password =
    LRQ returns all candidates(0)
    Maximum LRQ Hops = 0
    WAN Call Limit = 0 (disabled)
    LCF/LRJ V3plus = 0
    Gatekeeper Option Flags:
    Use IP Header Address = no(0)
    Ridgeway ARQ = no(0)

    Border Element
    —————–
    Static Routing
    No Static Routes configured

    DSP

    Voice Coding algorithm = 68
    Voice Information Field size = 160 bits
    Silence Suppression = Enable(1)
    Minimum Jitter buffer = 60 msec
    Maximum Jitter buffer = 300 msec
    Receive Gain (PCM -> IP) = -2 dB
    Transmit Gain (IP -> PCM) = -4 dB
    Digit Relay = 1
    Fax Relay Type = 0
    Fax Maximum Rate = 144
    Fax Playout FIFO nominal delay = 600
    Fax Modem Coding = 0
    Idle Time = 0
    Answer Supervision Options = 2

    AutoSwitch
    ———-
    Auto Threshold = 50

    H323 Gateway
    —————–
    Primary GK Address = 66.10.2.209
    Primary Auto Discovery = 1
    Secondary GK Address = 0.0.0.0
    Secondary Auto Discovery = 0
    H.323 ID = naples01.gw.usa
    Register DN = No(0)
    Ignore Bandwidth in ACF = yes(1)
    Default H245 Tunneling = yes(1)
    Round Trip Delay = 0
    One Stage Dialing = 0
    RRQ Interval = 180
    H323 Interop Flags:
    H225 GW Protocol = h323(0)
    Do BRQ = 0
    SlaveSessionId0 = 0
    AllowFastStartOnly = Yes(1)
    RRQv3plus= No(0)
    ProgressInd Alert= No(0)
    StartH245Flag= No(0)
    Automatic Ext IP Update= No(0)
    RTP Verification= No(0)

    Do Lightweight RRQ = yes(1)

    Radius User
    ———–

    host p 66.10.2.209
    authenticationport p 1812
    accountingport p 1813

    host s 0.0.0.0
    authenticationport s 1812
    accountingport s 1813

    retry = 5
    timeout = 10
    accountingtype = 2
    billingvendor 1
    sharedsecret *******

    IVR
    ——

    Primary File Server: IP Address = 66.10.2.209
    Secondary File Server: IP Address = 0.0.0.0
    timeout: 10

    Enabled Languages: 0

    CID Translation Table
    ——
    Caller ID Translation Table
    Index Pattern Replacement

    Radius Endpoint
    —————

    host p 0.0.0.0
    authenticationport p 1812
    accountingport p 1813

    host s 0.0.0.0
    authenticationport s 1812
    accountingport s 1813

    retry = 3
    timeout = 5
    idtype = 0
    passwordtype = 0
    sharedsecret

    Product Name: Tenor Digital Multipath Switch – 24 ports (Rev. B)
    Gatekeeper Status: Mini
    GK Calls Allowed: 16
    Feature Bit Status: -PS/+RB/-ER
    Languages allowed: 1
    Serial Number: A001-000B2E
    Ethernet Address: 00-30-E1-00-0B-2E
    IP Address: 65.40.42.209
    Subnet Mask: 255.255.255.128
    Default Gateway: 65.40.42.129
    System Software Version: P4-2-20-20(LEC) (1830074/0xD44E)
    Boot Software Version: P4-1-3 (180590/0xA9E6)
    Database Version: 2.08 09-13-2000 (277900)

    #23003
    kumar
    Guest

    I had a few question about a tenor A800 .with tenor iam using cellsocket what is the confg please help me .

    Thanks and hope you can help me.

    #23004
    Imran
    Guest

    Kumar, We are using cellsocket with quintum a400, so the same settings would be for tenor 800, the cellsocket gives voltage of only 24v against the required 48v to the tenor ports, so the voltage has to be adjusted in the tenor, ask your service provider to change that setting in the tenor

    #23005
    KUMAR
    Guest

    Hi Imran,

    CAN U HELP ME OUT IN THIS HOW TO CONFIG THE A800 TO ADJUST THE VOLTAGE .

    THANKS
    KUMAR

    #23006
    imran
    Guest

    kumar, send me in your config and i will check with mine and let you know what to change, the change was done by my service provider, so i need to cross check, email me at info@dial2globe.com
    imran

    #23007
    Sandeep
    Guest

    Hello Friend,

    I have two Tenor A400. i want to setup two location . but i have one side 8 Real Ip . and another i dont have real ip . Plz Email me both unit work or not . and how to setup unit. plz email me

    #23008
    BAHMAN
    Guest

    HI DEAR MANAGER ,
    I HAVE THE VOIP STATION WITH 10 UNIT OF TENOR A800 , I CAN USE WITH RADIUS FILES , BUT I NEED TO USE WITH CDR FILES BECASE THE CDR FILES MORE COMPLETE INFORMATION THAN RADIUS FILES .
    I CONFIGURED ON TENOR ( CDRSERVERIP , CDRSERVERPORT ( 9002 OR 9003 ) , CDRPASSWORD ) BUT I DONT KNOW IN MY COMPUTER SERVER WHICE SECTION OF WINDOWS COMPONENT MUST BE CONFIGURE FOR RECIVING THE CDR FILES FROM TENOR . PSL HELP ME IF YOU CAN.
    THANKS AND BEST REGARDS
    BAHMAN BANIADAM
    DORSA COMPUTER
    MAILTO : bahman_baniadam@hotmail.com

    #23009
    okechi
    Guest

    pls i want setup ivr server to work with my tenor A800.Thus could any one help recommend a cheaper software(voice software) to use for the ivr ( i want to start a prepaid calling card system)

    OKECHI

    #23010
    reza
    Guest

    hello,
    when i enter GateWay IP for tenor A800 it does not work . it is falling to a loop of reset and password command prompt doesn’t come. and when i clean the gateway and put that 0.0.0.0 it will work correct. what must I do? plz email me. thank u

    #23011
    cypherdecode
    Guest

    I have a Quintum A800, ASR is low because of too many “Cause Code 16” (Normal Call Clearing). The manual says “The cause indicates that the call is being cleared because one of the user has requested that the call be cleared.”

    Anybody knows what’s causing this code to occur?

    #23012
    www.blue-lava.co.uk
    Guest

    Hi Reza,

    It is a common set up problem on Quintum that when you enter the IP information the machine then goes into a loop of rebooting.

    This is because the subnet and the IP number you have chosen do not match up – this is often due to mis-keying the information (I know, I’ve done it myself more than once!).

    To rectify the problem boot the Quintum with a console cable plugged in the front – then press [RETURN] when prompted. You will then be able to reset the parameters.

    Hope this helps, if you need any further assistance please feel free to contact me at: mhitchcock@blue-lava.co.uk

    Thanks,

    Mat

    #23013
    nima
    Guest

    hi

    I have a problrm with quintum tenor stared at 3 day ago

    after a few minute tenor was reset automaticly and tenor`s alarm LED started blink and we reccived this errors
    217.66.217.161:1:rpt:1:critical softwear Error (VManagerProc(l7): failed to crate translator):0:0

    —–
    and finaly report this error

    tenor is in bypass mode

    at this time we must reset tenor manualy
    ———-

    please help me
    tnx

    #23014
    reza
    Guest

    dear mat; hi
    thank u
    but it seems IP and GateWay are working correctly and dosenot have any problem. because the PC that is pluged to the this IP and GateWay works without any problem.
    is there any command in tenor’s config that may be related with this problem?
    thank u again

Viewing 15 posts - 46 through 60 (of 205 total)
  • The forum ‘Voice over IP’ is closed to new topics and replies.