Generic selectors
Exact matches only
Search in title
Search in content

tenor A800

Viewing 15 posts - 91 through 105 (of 207 total)
  • Author
    Posts
  • #22828 Reply
    sudarsan
    Guest

    Hello,
    does any one help me, to configure windows xp for receving incoming calls from outside using PSTN modem.

    regards
    sudarsan

    #22829 Reply
    sudarsan
    Guest

    Hello,
    does any one help me, to configure windows xp for receving incoming calls from outside using PSTN modem.

    regards
    sudarsan

    #22830 Reply
    sudarsan
    Guest

    Hello,
    does any one help me, to configure windows xp for receving incoming calls from outside using PSTN modem.

    regards
    sudarsan

    #22831 Reply
    sudarsan
    Guest

    Hello,
    does any one help me, to configure windows xp for receving incoming calls from outside using PSTN modem.

    regards
    sudarsan

    #22832 Reply
    sudarsan
    Guest

    Hello,
    does any one help me, to configure windows xp for receving incoming calls from outside using PSTN modem.

    regards
    sudarsan

    #22833 Reply
    Cisco AS5350 to Tenor A800
    Guest

    Hi,

    Im using Cisco AS5350, i want my cisco to throw calls to a Tenor A800 with Tellular device…if I use an IP phone to test the quintum the call is successful but if I use the cisco to test call…it is not successful…pls. help…

    #22834 Reply
    Noname
    Guest

    Not much that could be wrong:

    1) Check codecs

    2) See if the quintum have restrictions on the “allowed” table about what I.P. addressese could send calls to it (very unlike)

    3) The call itself. Does the Cisco sends the calls a diferent way (I.E. with a prefix??)

    4) Go to the Quintum, enable event log by typing ev +ch and ev +q931

    That will put ont he log the attemps. Compare the log of the sucesfull call with the log of the failed calls.

    mike3799@yahoo.com

    #22835 Reply
    Narroo
    Guest

    Message to NONAME – Quintum & ADSL

    Hi Noname, thanks for the help on the forum. I am currently stuck with gateway to BE registration via ADSL. The BE receives the registration requests from the GW, but the IP address it receives is the one of the GW as it sits behind the ADSL router, and not the dynamic Public IP. Kindly indicate the possible config steps.

    Thanks

    #22836 Reply
    voipman
    Guest

    hello this voipman and i would like how much does a voipswitch software cost which supports
    A800 in generating Billing and CDR online.

    #22837 Reply
    zia
    Guest

    how can i configure one to one quintum a800 model

    #22838 Reply
    MikeM
    Guest

    Zia,

    If you mean configure 2 Tenors so that Port 1 of unit 1 is mapped to Port 1 of unit 2, you can use the port mapping feature. You can find information about this configuration on Quintum’s web site at
    http://www.quintum.com/support/1G/kb/telco/IP_Port_Mapping.pdf

    #22839 Reply
    elie…
    Guest

    Hi,

    Activation of Fake ring tone.

    I have calls originated from Cisco to my quintum. The pstn have a PDD of 20seconds. We did the activation of Fake ring tone, and the caller from Cisco is able to hear the fake ring tone even if there is dead air for 1 min, but the problem is if someone answer on the other end, the fake ring tone never stop ringing…and it looks no one answered the phone.

    i have analogue A800.

    What i have to do in this position.

    Regards
    Elie

    #22840 Reply
    mevren
    Guest

    hi.ı use a adsl gateway.(include nat and firewall).ı have a analog a800 quintum device.ı must configure quintum device behind the nat.ı suppose to configure a command which name is auto external ip.ı configure auto external ip enabled.but not configure.because a800 quintum device doesnt accept this command.
    my quintum device
    system software version:P4-2-15(lec)
    boot software versionP4-1-3
    database version:2.08 09-13-2004
    please help me.

    mevren@yahoo.com

    #22841 Reply
    NCt
    Guest

    i got a situation whit the tenor a800 result that i change The Ip gw and submask but when i reboot The unit it telling me that get a SNMP error values ( simple network manager protocol ) or agent yu knew that , thepint now is tha by console i cant set the unit becuase itdoesnt given to me the Option to do becuase is rebotin , can yu tell me how i fix my situation or The way to dowload the software and instaled i Knew is problem software but i dont realy Knew how to Install new or fresh copy or correct the software and i i have it i got from the quintum site .

    thank for yur help
    software1@hotmail.com

    #22842 Reply
    Nikki
    Guest

    My query is, how much memory is utilized by one IVR session in cisco 5350 for making a VoIP call using E1 line.

Viewing 15 posts - 91 through 105 (of 207 total)
Reply To: tenor A800
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">