- This topic is empty.
29th November 2006 at 13:32 #22933MikeM to JustinGuest
I am a little concerned here as there could be more than one problem.
The first question is, are you able to detect dialtone from this gsm device when you use the test command? If so, then the basic is ready.
The second question/concern is you say that this is a GSM modem. Does this mean that you will be doing data/modem calls and not voice calls? If this is the case, then I have never seen pure data/modem calls work through an A800 before, and I have seen a lot A800’s.
If you are doing just voice, then do not set any of the modem stuff as the GSM device is not a really a modem.
Please clarify this and feel free to contact me at my email of firstname.lastname@example.org
MikeM4th December 2006 at 05:47 #22934allanGuest
hi to all,
anyone can give me a complete configuration of quintum A800 using PBX to PBX setup.
Allan4th December 2006 at 14:01 #22935MikeM to allanGuest8th December 2006 at 06:41 #22936RustyGuest
I am having the following error on AX2400,
22:ALR:1:Call Handler not Registered with Gatekeeper:0:0:0:0:FRI DEC 08 09:29:34 2006
23:CLR:1:Call Handler not Registered with Gatekeeper:0:0:0:0:FRI DEC 08 09:29:49 2006.
Every few seconds, pls advice. thanks8th December 2006 at 14:01 #22937MikeM to RustyGuest
if you are using epad, make sure that you have the tenor’s own ip address in the allow table. Also, make sure that you are at the latest software version.
email@example.com December 2006 at 15:57 #22938SajibGuest
I have problem with my quintum.
Problem is call comes in my gw but it doesn’t get activated.
The calls show call proc, then after 10 sec it becomes term disc(19).
I am using pstn lines. I’ve done test dial, and seems fine.
Please help me and thanks in advance to all the posters.10th December 2006 at 04:56 #22939MikeM to SajibGuest
It may be a problem with your answer supervision configuration. You can check this against quintum’s recommendations by reviewing their answer supervision doc on their website under support, search for answer supervision.
If you need further help, you can contact me directly.
firstname.lastname@example.org December 2006 at 12:11 #22940ABDUL HALIMGuest
pls. anyone help me the configuration smple of quintum. pls. pls.
email@example.com December 2006 at 13:35 #22941MikeM to AbdulGuest
I have sent you an email. Please review and respond. thanks
firstname.lastname@example.org January 2007 at 08:40 #22942avhiGuest
gatekeeper show that calls r running but actually the calls r not running.after a few moments the calls r found in finished calls with cause code 16,34.quintum gateway also cant show the calls when calls r running.pls give me the answer19th January 2007 at 13:37 #22943MikeM to avhiGuest
There are many reasons that this could happen. A 16 is usually when the call originator hangs up. 34 is usually when a call comes to the quintum that either presents a dialed number that is not configured in the quintum or no dialed number is present.
This would require more troubleshooting to determine the reason.
email@example.com July 2007 at 19:34 #22944SabuzGuest
One thing that is when i put
# test o 1
then the LED of first PSTN is blinking
again when i put
# test o 5
then the LED of first PSTN is blinking again
please help me to congigure both pbx and pstn ports