Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

2nd dail (quintum)

Viewing 15 posts - 1 through 15 (of 178 total)
  • Author
    Posts
  • #22498
    xuey
    Guest

    How to config 2nd dail on tenor A400?

    I only config IVRTYPE = 1, but I dail into A400, may hear a 2nd dail tone ,and I dail destination’s number ,but no response ,log file shows bad format number

    can yuu help me ,give me a sample configuration?

    #22499
    spam hater
    Guest

    Telnet into the unit and log in. Once you get the prompt, type gk and enter.
    At the gatekeeper prompt,type gk route and the number that you are dialing.
    For example if you are calling to Argentina you will type 01154 plus the area code and the number.
    The A400 will answer witha list of the gateways that could take your call at that moment.
    If it returns a “no candidates”. the number that you are dialing is not right.
    You could also see who is registered on your unit by typing
    gk ep return
    That will give you a list of all the numbers reacheable from your a400.
    Give a holler if you need more help.
    Remove the first part nobswboyrie@yahoo.com
    Start with the “w”

    Good luck!!!!!

    #22500
    xuey
    Guest

    thanks ,I can see the number that I dialed in gk table.
    if i dial from tenor A400 to another tenor A400 is right ,I guess that the route is right.

    so I can’t find out the problem .

    the log

    Quintum:beijing e +ch cas ivr
    e +ch cas ivr
    Event Log Add To Mask…
    Enabled Modules: excp ch cas ivr
    Quintum:beijing

    Quintum:beijing

    Quintum:beijing

    Quintum:beijing

    Quintum:beijing e
    e
    Dumping Event Log…
    Product Name: Tenor Analog A400 Multipath Switch – 4 ports (Rev. B)
    Gatekeeper Status: Mini
    GK Calls Allowed: 4
    Feature Bit Status: -PS/+RB
    Languages allowed: 1
    Serial Number: A002-001A27
    Ethernet Address: 00-30-E1-00-1A-27
    IP Address: 192.168.0.20
    Subnet Mask: 255.255.255.0
    Default Gateway: 0.0.0.0
    System Software Version: P4-2-7+(Raj-11/7/2002)(LEC) (1774551/0x0F16)
    Boot Software Version: P4-1-3 (180592/0xE814)
    Database Version: 2.08 09-13-2000 (267200)
    Time (since last reset): 2719 seconds

    CAS : 266576:Received Message
    CAS : 266576:mtype = 64
    CAS : 266576:CAS: HL Message
    CAS : 266576:CAS: ABCHANGE Message
    CAS : 266576:Process AB change: [2,1] ABCD=0x0.
    CAS : 266576:[2,1] Set Disc States
    CAS : 266576:LocalDiscState = 0
    CAS : 266576:RemoteDiscState = 0
    CAS : 266576:HL Event = 11
    CAS : 266576:[2,1] casProc: Idle-Seizure
    CAS : 266576:Sent Msg to Usid = 44
    CAS : 266576:[2,1] Sent SETUP to CH
    CAS : 266576:[2,1] New State = 6
    CH : 266576:[2: 1] received message from cas: Setup
    CH : 266576:CallInfo[0xd7f428]: origCalled.digit()
    .
    CH : 266576:[2: 1] sent message to cas: Call-Proc
    CAS : 266576:Received Message
    CAS : 266576:mtype = 128
    CAS : 266576:CAS: ISDN Message
    CAS : 266576:Process ISDN Message [2,1]: imsg=3.
    CAS : 266576:In decode: message code = 3
    CAS : 266576:[2,1] Decode CALLPROC
    CAS : 266576:[2,1] casProc: i3-CALLPROC
    CAS : 266576:Sent Msg to Usid = 44
    CAS : 266576:[2,1] Sent INBANDSIGDONE to CH
    CAS : 266576:[2,1] New State = 6
    CH : 266576:OBCSM[20]: pin: .
    CH : 266576:Routing requested for: public(1) orig=1 public(0) normalized=1111* route code= .
    CH : 266576:1 match(es) found: 0
    CH : 266576:IVR(0xd7dc04): Instantiating new IVR.
    CH : 266576:IVR(0xd7dc04): peerRcvSetup
    CH : 266576:IVR[0xd7dc04]: pin: 1.
    CH : 266576:IVR Type=1 PIN=
    CH : 266576:[2: 1] sent message to cas: Alert
    CH : 266576:OBCSM[20]: Received peerRcvConnect.
    CH : 266576:[2: 1] sent message to cas: Connect
    CH : 266576:[2: 1] received message from cas: InbandSigDone
    CH : 266576:tsi connect: 001 208 01
    CH : 266576:TsiConnXlate: 0:1, 2:8
    CH : 266576:tsi connect: 001 208 10
    CH : 266576:TsiConnXlate: 2:8, 0:1
    CAS : 266576:Received Message
    CAS : 266576:mtype = 128
    CAS : 266576:CAS: ISDN Message
    CAS : 266576:Process ISDN Message [2,1]: imsg=4.
    CAS : 266576:In decode: message code = 4
    CAS : 266576:[2,1] casProc: i3-ALERTING
    CAS : 266576:[2,1] New State = 6
    CAS : 266576:Received Message
    CAS : 266576:mtype = 128
    CAS : 266576:CAS: ISDN Message
    CAS : 266576:Process ISDN Message [2,1]: imsg=5.
    CAS : 266576:In decode: message code = 5
    CAS : 266576:[2,1] Decode CONNECT
    CAS : 266576:[2,1] casProc: i3-CONNECT
    CAS : 266576:[2,1] Set Disc States
    CAS : 266576:LocalDiscState = 1
    CAS : 266576:RemoteDiscState = 0
    CAS : 266576:[2,1] Send Answer to Line
    CAS : 266576:[2,1] Send ABCD = 15
    CAS : 266576:[2,1] New State = 7
    CAS : 266584:Received Message
    CAS : 266584:mtype = 64
    CAS : 266584:CAS: HL Message
    CAS : 266584:CAS: ABCHANGE Message
    CAS : 266584:Process AB change: [2,1] ABCD=0x5.
    CAS : 266584:HL Event = 7
    CAS : 266584:[2,1] casProc: Disc-Idle for incoming call
    CAS : 266584:ixDiscIdle: ignoring ring-off/idle ab-change
    CAS : 266584:[2,1] New State = 7
    CH : 266676:IVR(0xd7dc04): ProcessTimerExpiration. State=1
    CH : 268676:IVR[0xd7dc04]: Bad number format dialled: .
    CH : 268676:IVR(0xd7dc04): Aborting IVR.
    CH : 268676:tsi disconnect: 208 001 01
    CH : 268676:TsiDiscXlate: 2:8, 0:1
    CH : 268676:tsi disconnect: 208 001 10
    CH : 268676:TsiDiscXlate: 0:1, 2:8
    CH : 268676:OBCSM[20]: Release from peer=0xd7dc04 cause=0x1c redir=.
    CH : 268676:CallInfo[0xd7f428]: cdr callid(14) rmtcallid(0) calltype(1) destnumtype(0).
    CH : 268676:CallInfo[0xd7f428]: cdr dest(1111*) orig() remote() pin().
    CH : 268676:CallInfo[0xd7f428]: cdr icline(1) icport(0) otline(ff) otport(405465).
    CH : 268676:CdrManager::addCdr: 19 Return.
    CH : 268676:CallInfo[0xd7f428]: sendDisconnected Event.
    CH : 268676:tsi connect: 001 201 10
    CH : 268676:TsiConnXlate: 2:1, 0:1
    CH : 268676:CallInfo[0xd7f428]: sendDisconnected Event.
    CH : 268676:[2: 1] sent message to cas: Alert
    CAS : 268676:Received Message
    CAS : 268676:mtype = 128
    CAS : 268676:CAS: ISDN Message
    CAS : 268676:Process ISDN Message [2,1]: imsg=4.
    CAS : 268676:In decode: message code = 4
    CAS : 268676:[2,1] New State = 7
    CH : 270476:OBCSM[20]: Disconnecting tone (previously connected).
    CH : 270476:OBCSM[28]: cause = 10489532
    .
    CH : 270476:tsi disconnect: 001 201 10
    CH : 270476:TsiDiscXlate: 2:1, 0:1
    CH : 270476:[2: 1] sent message to cas: Disc
    CAS : 270476:Received Message
    CAS : 270476:mtype = 128
    CAS : 270476:CAS: ISDN Message
    CAS : 270476:Process ISDN Message [2,1]: imsg=6.
    CAS : 270476:In decode: message code = 6
    CAS : 270476:[2,1] Decode DISC
    CAS : 270476:[2,1] casProc: DISC for incoming call
    CAS : 270476:[2,1] casProc: Disc Proc
    CAS : 270476:discProc: local disc state = 1
    CAS : 270476:discProc: remote disc state = 0
    CAS : 270476:[2,1] Send Disc-Idle to Line
    CAS : 270476:[2,1] Send ABCD = 5
    CAS : 270476:LocalDiscState = 0
    CAS : 270476:[2,1] Start Delay, ID = 8
    CAS : 270476:[2,1] New State = 10
    CAS : 270581:Delay Event = 8
    CAS : 270581:Stopped Delay D = 8
    CAS : 270581:[2,1] casProc: x5x-D8
    CAS : 270581:Sent Msg to Usid = 44
    CAS : 270581:[2,1] Sent RELCOMP to CH
    CAS : 270581:[2,1] New State = 0
    CH : 270581:[2: 1] received message from cas: RelComp

    #22501
    Amir
    Guest

    PLZ help me for ip address config in tenor A800

    TX

    #22502
    Quiensabe
    Guest

    To enter a new I.P. address for the tenor:

    Login into the machine
    From the prompt type “config”
    Now the prompt is “config#”
    Type “unit 1”
    Prompt is now “config unit 1#”
    type Ip zzz.222.sss.ddd.

    After you do enter the I.P.adress, you need to type “submit” for the terminal to keep the setting.
    The changes will not be efective until you reset or reboot the unit.

    You could use the “reset” command to do that.

    If you have a e-mail that could hold around 2.8 mb, I could send you the whole quintum tenor manual.
    No one working in a tenor should be without it.
    be sure that you could receive around 3mb file.
    Post your e-mail address and I will send it to you.

    #22503
    kanningcai
    Guest

    Quiensabe: could you please send me tenor manual?

    sueking@shuxun.net

    #22504
    Jessie
    Guest

    Quiensabe,

    Hi. I wonder if you can do me a favor. Can i have a complete copy of your quintum manual? I. currently setting up quintum d3000 and having a hard time in configuring it. I really much appreciated if you can email it to: jdmjamboo@hotmail.com and/or jdmjamboo@yahoo.com.

    #22505
    quiensabe to Jessie
    Guest

    Manual was sent to your address

    If anyone else need a copy of the CLI manual (soft) write me a mike3799@yahoo, and I will send you the file.

    The file is large. Be sure that there is room on your e-mail acccount.

    Good luck!!!!!

    #22506
    Druid
    Guest

    Quiensabe: could you please send me tenor manual?

    ip_tel@hotmail.com

    #22507
    don to quiensabe
    Guest

    Hi can you please send me a copy of that Quintum Manual.

    Thanks!

    email: donxvii@info.com.ph

    #22508
    Asi
    Guest

    in the event log there is a referance number beside each event,
    is there any way to query this event deeper ??

    #22509
    Matt
    Guest

    Hello, You can set the level of the event log. Email me for specifics. Mattg@telcomproducts.com

    #22510
    Austin
    Guest

    I want to make simple conection between two tenor having single phone at both side.

    I have made sroute & what else configuration has to implement.

    #22511
    noname
    Guest

    If you need to call from a single line phone to a single line phone, it is very simple.

    You need to asign a phone number to the ports where the phonew is attached to .
    Lets say site “A” have a phone on port one. All what you need to do is assign a number (real or other) to the port. That becames the phone number to that port.
    It is simpler to keep the internation format, since Quintum route calls following that format.

    Lets say that location “A” is in New York. You tell the Quintum that:

    1) Country code is 1
    2) Area code is 212
    3) Port 1 is 555-1212
    4) Port 2 is 555-1213

    When a call arrives ,via voip that have the number 1 212 5551212, the quintum will look up on the table and route it to port 1.

    If you need a sample configuration,email me mike3799@yahoo and I could send you a sample for a A400.

    Regards!!!!

    #22512
    VoIP
    Guest

    Hello , i have a quintum a400 tenor (analog series).. also ivr and radius server.. when call ended from both side (my tenor and destination number) quintum’s led turn off after one minute later.In pstntg prompt i’ve configured cassignaling to 1 and supervision 3.. Then same problem occured. And then i’ve changed casssignaling to 6 (loop fast and disconnect) and supervision 3 same problem occured too.. There is no wrong charge…Radius calculates the true calling time.. How can i solve this problem?

Viewing 15 posts - 1 through 15 (of 178 total)
  • The forum ‘Voice over IP’ is closed to new topics and replies.