Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

audio problem with cisco5300

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • #21327
    izumi
    Guest

    hello,

    we experienced an audio problem during the call connection.Caller can hear nothing after dialing a destination number. In fact call is connected.(it shows “normal clearing”in call log).
    Anybody has the familiar experience?Or pls give us some clues.

    Thank you.

    #21328
    Aushman
    Guest

    Hi izumi,

    Please check your IOS version .Try to compair with your other end or upgrade to 12.2 Xbi ..

    Also If you have no ringing problem you need to insert some commands in your far end gateway.

    #21329
    izumi
    Guest

    hello Aushman ,

    Thank you for your help.
    the originate gateway is with
    IOS Version 12.1(3a)T1,we can not upgrade it to higher ver, since it is limited by the size of flash memory(8MB).
    We made a call successfully on originate cisco (using csim command),it can ring the destination(mobile phone). But when we try from phone–pstn-
    pbx-originate cisco–IP,it failed to ring the destination.
    We have tried to extend wait_release time on both side(cisco) but still nothing
    changed. IOS Upgrading is the only solution ?

    #21330
    Aushman
    Guest

    Hi izumi,

    Can you send me the Voice-port config postion to my email account umindaj@yahoo.com

    #21331
    joemai
    Guest

    Hi Mr. Aushman,

    Have you resolved the problem of Mr. Izumi? We too have the same problem. Please help!

    #21332
    Teodor Georgiev
    Guest

    Check if it is not a codec mismatch problem. Run a debug (debug cch323 h225) and look at the output.
    Also, check for any access-lists on the way that might block the UDP (RTP).

    #21333
    joemai
    Guest

    Thank you sir for attending our problem.

    Upon running a debug, we monitored that we are not getting any TX Answer signal. Also when we show call active voice the output looks like this:

    22A4 : 5565690hs.1 +-1 pid:0 Answer connected
    dur 00:00:00 tx:137/4393 rx:0/0
    IP xxx.xxx.xx.xxx:49654 rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms gsmfr

    22A4 : 5565691hs.1 +-1 pid:122 Originate 22011639174123045 connecting
    dur 00:00:00 tx:0/0 rx:137/4393
    Tele 1/2:1 (110) [1/2.0] tx:12800/2000/0ms gsmfr noise:-63 acom:127 i/0:-52/-
    7 dBm

    Telephony call-legs: 1
    SIP call-legs: 0
    H323 call-legs: 1
    MGCP call-legs: 0
    Multicast call-legs: 0
    Total call-legs: 2

    You will notice that the ouput codec is gsmfr, but we set this as g729r8.

    #21334
    Teodor Georgiev
    Guest

    See that you are not getting any voice from the other side:


    tx:137/4393 rx:0/0″

    Do you hear a ringback ?
    If not, have you configured the progress indicator items at your dialpeers ?

    #21335
    joemai
    Guest

    Sir there was an error in our log:

    %SIGSM-1-NO_TEMPLATE_ERR: No static template found for slo
    t 3 port 3 with parameters provided

    What is the cause of this error? We’ve searched the net and it says Signaling service manager. We also can’t hear a ringback tone. Maybe because of signaling.

Viewing 9 posts - 1 through 9 (of 9 total)
  • The forum ‘Voice over IP’ is closed to new topics and replies.