- This topic has 14 replies, 1 voice, and was last updated 17 years, 10 months ago by Appan KH.
18th February 2002 at 11:12 #21227Ian SmithGuest
I have a cisco5300 to cisco5300 connection between london and another location , where the cisco is connected to a carrier access channel bank which in turn is connected to normal pstn lines.
The call seems to be hitting the channel bank fine as engineer can patch into channel bank and hear me , but channel bank does not seem to send call on.
Has anyone faced this problem before.
Thanks21st February 2002 at 01:33 #21228RommelGuest
Yeah sounds like an answer supervision issue with the channel bank. Go with Adtran’s intelligent one…i cant remember which one it was but the carrier access corp seems to have some timing issues with their answer supervision.21st February 2002 at 02:31 #21229TACGuest
See the “answer supervision” post above this one. If you want great ASR values, the Pleiades Communications Channel bank has an option that uses tones and voice to generate answer supervision. The same option can provide disconnect supervision that prevents “hung channels”. http://www.pleiadescom.com6th March 2002 at 07:11 #21230tehGuest
could you explain what is the definition of ASR. HOw’s the diff beteen the ASR for Voice over PSTN switch and VoIP? Do we consider poor internet connection as bad ASR?
Thanks.10th March 2002 at 16:10 #21231JuniorGuest
I think you have confused Adtran with Pleiades unit. The Pleiades unit is the only CB that detects voice for answer supervision.18th April 2002 at 13:10 #21232GrahamGuest
I am looking to connect several sites up over pstn lines, using VoIP, can anyone recommend any products?
Graham14th June 2002 at 15:27 #21233Greg VanceGuest
I suggest you go to Linux-support.net web site. You’ll find a product called Asterisk that will support VoIP and they also have hardware cards available (E1 and FX0) .17th June 2002 at 02:20 #21234NCGuest
I recommend the Pleiades T1 VAD (real ASG) Units, Those are the ones i use most often in the field. Work like a charm and are the best priced babies in the category.3rd August 2002 at 22:27 #21235RaulGuest
try the Orion channel bank with voice activity detection. Works excellent. http://www.oriontelecom.com18th October 2002 at 11:12 #21236PremnathGuest
I have 30 PSDN line and these are connected to E1 card in my Lucent PABX via Pleiades CB. The problem is when I dial a call from the PBX extention, the call goes through and after call is answered, the line gets disconnected in about 5 secs. Anyone has any solutions?
Premnath28th October 2002 at 05:52 #21237ZopaGuest
Answer supervision as noting to do with what Ian Smith explained “channel bank does not seem to send call on”..
AS or DS leads to inacurate billing system. if a call does not connect, that does not mean it ‘s AS prb.
in Ian Smith ‘case, he problem may likely be signalling or switche(s) setting on the Channel Bank/signalling24th November 2002 at 01:41 #21238Hi Zopa,Guest
Actually you are incorrect, in order for the egress gateway to send the h.225 connect it needs to understand that the “line” has connected. Without answer supervision, no connect, without any connect, no billing.15th December 2002 at 21:03 #21239OKONGuest
WE ARE A BUDDING ISP FACED WITH DIRE COPPER SHORTAGE, WHICH MAKES IT ALMOST IMPOSSIBLE TO ADD MORE VOICE CIRCUITS TO OUR NETWORK.
THE OPTION WE ARE TOLD IS TO DEPLOY A “CHANNEL BANKS” EQUIPMENT ON THE PSTN END AND OUR POP THAT TAKE TWO PAIRS OF COPPER WIRE AND BREAK THE SIGNAL OUT OF THEM INTO 24 SEPERATE VOICE CHANNELS.
DOES ANYONE HAVE A SOLUTION?
CIO6th February 2003 at 17:22 #21240AhmadGuest
Use the Orion E1 or T1 GSM channel banks. No answer supervision issues. It is the best solution I have seen available so far.
http://www.oriontelecom.com6th February 2003 at 17:35 #21241Appan KHGuest
The channel bank is for to connect E1/T1 to analogue lines. The channel banks are complex in nature and difficult to maintain. The best solution is to go in for analogue gateways like Tenor 800,etc..