Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

2g huawei

Viewing 15 posts - 1 through 15 (of 51 total)
  • Author
    Posts
  • #63391
    suresh
    Guest

    Hi,

    i am new to huawei system and i worked on eric system.so can u help me to find parameters in huawei for voice like

    half rate to full rate parameter,

    full rate to half rate parameter,

    intra cell handover parameter,

    queuing,cls parameter

    and in gprs

    ondemand pdch parameter,

    spdch

    dynamic allocation

    in uplink 4 timeslot

    plz help…….

    #63392
    Bijoy
    Guest

    Hi Suresh
    half rate to full rate parameter-Ratio of TCHH(%)
    full rate to half rate parameter-TCH Traffic Busy Threshold(%)
    intra cell handover parameter-Intracell HO allowed
    queuing-Allow EMLPP
    cls parameter-Load HO Allowed
    ondemand pdch parameter-Maximum Ratio Threshold of PDCHs in a Cell(%)
    spdch-Huawei doesn’t have SPDCH concept.
    dynamic allocation-PDCH reforming
    uplink 4 timeslot-Allocate Two Timeslots Switch for MS over Uplink.Till C12 version huwai supprts only 2 TSL in UL.

    Br\\
    Bijoy

    #63393
    Pix
    Guest

    Bijoy is back ! The forum is on fire this morning 🙂

    #63394
    suresh
    Guest

    Hi bijoy,

    thanks buddy great thanks a lot.

    still want to know abt some parameter

    here pdch reforming is for PS to CS.

    but which parameter is for CS to PS. IF THERE IS PLZ TELL. because if i am defining dynamic pdch and there is more cs traffic then it will preempt my edge pdch.
    So plz tell this also if possible plz tell which are there counters.

    #63395
    Bijoy
    Guest

    Hi Suresh
    Check out these parameters
    1.Level of Preempting Dynamic Channel
    2.Reservation Threshold of Dynamic Channel Conversion
    For counters,check R93* counters

    Thanks Pix.Hope you will arrange some water:-)(kidding dear)
    Br\\
    Bijoy

    #63396
    suresh
    Guest

    Hi bijoy,

    can we do half rate to full rate and full rate to half rate with quality threshhold like eric.

    #63397
    Bijoy
    Guest

    Sure ,there is.
    1.IntraCell AMR TCHH-TCHF Qual Ho Allowed
    2.IntraCell AMR TCHH-TCHF Ho Qual. Threshold
    3.IntraCell AMR TCHF-TCHH Ho Qual. Threshold
    4.IntraCell AMR TCHF-TCHH Qual Ho Allowed
    & there are also criteria like Pathloss,ATCB etc

    Br\\
    Bijoy

    #63398
    suresh
    Guest

    Hi bijoy,

    thanks buddy here i am facing the problem of poor ho sucess at bsc boundries within same msc everywhere in my network so by enabling handover power boost will help to improve ho sucess?

    and one more thing buddy in eric for gprs harware side we are checking gddm capacity how many rps? so for huawei how to check and whats its capacity?

    #63399
    Bijoy
    Guest

    Hi Suresh
    HPB will definitely supress the poor radio environment.Also try increasing the Timers T3107 & T3121.

    Like RPP in Er\\,in huawei we have GDPUP(PCU).
    Max PDCH(static+dynamic) per PCU =1024.
    Max cells per PCU =2048
    Max PDCH per BSC=8192.
    Max PCU Num=32.

    Br\\
    Bijoy

    #63400
    suresh
    Guest

    hi bijoy,

    Buddy by hopwrboost u are telling my ho sucess improve at bsc boundries ok? BUt will it affect my tch drop because interference will increase ?

    And buddy u are telling 32 pcu ?is it per bsc ?i mean like eric in one gddm we can put max 7 rpp and if its 100% utilized then i have to put another gddm.and in eric,nokia only one pcu in bsc so herein huawei can u plz explain?

    #63401
    optimizer
    Guest

    hi suresh.

    What software r u using for monitoring Um and Abis interface. How can i detect in huawei that bts internal alarms r not active(lets supose huawei want to hide them).

    #63402
    Bijoy
    Guest

    Hi Suresh
    HPB will not impact TCH Drop.
    Rgarding PCU,this is what I know for BSC6000.

    Regarding Nokia,max no. of logical PCU for BSCi was 8+1,higher versions have much more,say the latest flexi BSC have 60+10 logical PCU.

    Br\\
    Bijoy

    #63403
    SURESH
    Guest

    HI BIJOY

    THANKS BUDDY I HAVE STILL ONE CONFUSION WITHOUT HO POWER BOOST HOW MUCH POWER IS RADIATED BY BTS? I THINK IT IS MAXIMUM OR SOMEWHAT LESS?

    #63404
    Bijoy
    Guest

    Hi Suresh
    With HPB, the BTS transmit power is adjusted to the maximum before the BSC sends a handover command to the MS. In addition, the BTS transmit power is not adjusted during the handover to ensure the success of the handover.

    When the receive level of an MS drops rapidly, a handover occurs. In this case, the BSC cannot adjust the transmit power of the MS and BTS in time. The MS may fail to receive the handover command, thus leading to the call drop.

    Br\\
    Bijoy

    #63405
    SURESH
    Guest

    Hi buddy ,

    Thanks for reply but check my question i want to know without ho power boost how much power will be radiated by bts ? is it max or less?

    and power control will come in picture?

Viewing 15 posts - 1 through 15 (of 51 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.