Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

HO Failure Leading to Increase in DCR

  • This topic has 17 replies, 1 voice, and was last updated 13 years ago by taupaji.
Viewing 15 posts - 1 through 15 (of 18 total)
  • Author
    Posts
  • #63123
    KJB
    Guest

    Hi Experts,

    What may the reasons for HO drops.
    How to improve by modifing parameters.

    Suppose HO are being failed 100%,88%,89% with adjucent neighbours.Neighbour defined are bidirectional already verified.BCCH TRX QUality is also OK (89),Vendor is NOKIA.

    Thx
    KJB

    #63124
    pix
    Guest

    Hi,
    Such poor QoS is either due to :

    1/ a terrible error in your frequency planning (same freq + same BSIC ?) (same frequency within the same BTS ?)
    –> in this case, call drop, cssr and voice quality must be very bad too…?

    2/ a software bug.

    Now I am not familiar with nokia, so I cant tell you how to fix a sw bug. But you could try deleting the BTS from the OMCR and re-create it from scratch. That might clean the system.

    Regards
    pix

    #63125
    KJB
    Guest

    Thanks Pix,

    Neigbour Audit is done and all seems OK.

    As far asa SW is concerned ,Same SW is working nationwide without any problem.

    BR.

    KJ

    #63126
    Pix
    Guest

    KJB,

    Your logic is flawless ๐Ÿ™‚

    My car can’t have a flat tyre, otherwise all other cars would also have had a flat tyre.

    Cheers
    pix

    #63127
    Bijoy
    Guest

    Hi KJB
    Have you seen ND Report 204??
    What is the reason for HO failure??
    Have u checked neighbour definitions fron ZEAP;??

    Br\\
    Bijoy

    #63128
    Mania
    Guest

    Hi KJB,
    Could you recreate the cell / problematic relation just to varify I have seen this to be helpful in some vendors (when all else fails). is HFR high for all adjacent neighbour or just one.. check its incoming is it bad with all then there might be hardware issue with that cell.

    Also get a DT done and try to catch the issue is field try to isolate any specific codec / region / scenario that might be generating the failures.

    @ Pix ๐Ÿ™‚

    #63129
    KJ B
    Guest

    Thx mania.

    @pix,
    SW has been reinstalled before Flawless Statement:):):)

    Dear Bijoy,

    Neigbour relation is verified (BCCH,BASIC etc)with ZEAP.
    ND report 153 show maximum HO failure with 3 site.
    DL quality of BCCH TRXs is OK as per ND report 196 on Sourc and Target Cells.
    I have used ND 154 in which maximum contribution is of Interference.

    Maximun failure is in outgoing HO failure that is 66%.

    Thanks for support.

    regard
    KJ

    #63130
    Bijoy
    Guest

    Hi KJB
    The trick given by Mania can work,actually it has worked many times.

    If you want to drill down more,have you checked the slips on the E1?(ZYMO).

    Also,you can put a trace for that particular cell to have a look at the failure messages.Maybe you will get a clue.

    Br\\
    Bijoy

    #63131
    KJ B
    Guest

    Hi Bijoy,

    Media is very stable,there are not any slips,es,ses using ZYMO.

    Will Try Mania Trick:)

    #63132
    Pix
    Guest

    I don’t want to goat but I said :
    “you could try deleting the BTS from the OMCR and re-create it from scratch”

    that’s what I meant by “sw bug”.

    So the Mania’s trick should be renamed “Mania & Pix”‘s trick ๐Ÿ™‚

    pix

    #63133
    KJB
    Guest

    :):) OK Sir Mania & Pix Trick:))

    Thanks

    KJ

    #63134
    jack
    Guest

    hi v.
    you said “you can put a trace for that particular cell to have a look at the failure messages”

    my vendor is nokia.
    how i can put a trace in cell in nokia BSC.
    please explain for me step to step.
    thanx

    #63135
    kamal kotecha
    Guest

    Hi,

    check 2745 Alarm in MSC,you will find the mis configured neighbours..You can check 2725 in BSC also..

    204 Report will be useful too..

    #63136
    Bijoy
    Guest

    Hi Jack,KJB
    In Nokia,a trace can be put on any cell of a BSC.
    Regarding trace of TCH drop—TCH observation
    SDCCH Drop-SDCCH Observation

    Handover-HO observation.

    All you need is to activate these counters

    P.S. Only one cell per BSC can be put on any of these observation

    Br\\
    Bijoy

    #63137
    Mania
    Guest

    Thanks everyone for giving me the honour of naming a procedure after my name and using Pix and my name in the same sentence ๐Ÿ™‚

    and you can also check for synchronization issues with BTS.
    These too result in Handover failures. how to check would be vendor dependent. for Alcatel the options of Sync_mode are GPS sync , PCM sync or free running clock… now if you have PCM synchronized and there are no slips then its ok or if its GPS sync and the signals are ok then too its ok. normally free running clocks can give you trouble.. In Alcatel SUMA ( the site processor) needs tweeking when this happens.
    Synchronization can effect Outgoing handover or Inc_HO or both of a cell / multiple cells of same site.
    If you find such parameter ‘Sunc_Mode” for Nokia do let us know for our information ๐Ÿ™‚

Viewing 15 posts - 1 through 15 (of 18 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.