Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DL power control and DL DTX

Viewing 8 posts - 16 through 23 (of 23 total)
  • Author
    Posts
  • #62644
    Dell
    Guest

    Hi Pix,
    outdoor is OK. The problem is indoor. In Idle the level is stable. After establishing the call, in Dedicated mode, in hopping TRXs, there is a drop in level (from -85 dBm in Idle there is a drop to -95 dBm in dedicated).
    Regards,
    Dell

    #62645
    Brother
    Guest

    if u dont have quality issue than no need to worry about power decrease that is power control, if yes disable hopping during the test, get channel verification test with tems and see the trx performance one by one.

    #62646
    Ian
    Guest

    Hello DELL,

    What are ur values for :

    L_RXLEV_UL_P
    L_RXLEV_DL_P

    U_RXLEV_UL_P
    U_REX_LEV_DL_P

    And pow_red_step_size, pow_inc_step_size, pow_red_factor, pow_inc_factor

    Just make sure you parameters ok.

    Ian

    #62647
    Dell
    Guest

    Hi Ian,
    thanks for your help. Here are operational params and default:
    L_RXLEV_UL_P= operational -87 dB (default -95)
    L_RXLEV_DL_P= -85 (def. -85)
    U_RXLEV_UL_P= -77 (def. -85)
    U_RXLEV_DL_P= -75 (def. -75)

    pow_red_step= 2 dB (def. 2 dB)
    pow_inc_step_size= 6 dB (def. 4 dB)
    pow_red_factor=1 (def. 0.5)
    pow_inc_factor=1 (def. 0.8)

    Should I change these params to default? And what about EN_BS_PC, should I disable it?
    Regards,
    Dell

    #62648
    Mania
    Guest

    @Pix: Great to be back, was overloaded with additional responsibilities.
    @dell:I know its late for this, but have you tried disabling Power control does the issue remain as it is now, if no then your issue is not related to power control. also is this cell concentric, as a call being assigned to DCS can effect levels too. Plus THIS IS VERY IMPORTANT “you haven’t told if you are experiancing quality within the window or degraded from it, if quality is within the window then there is no issue”.

    #62649
    Dell
    Guest

    Hi Mania,
    Thanks for your contribution.
    I changed parameters listed in my previous post to default parameters. Power control didn’t disabled yet. I’m going to do that on Monday. Quality is not the issue, of course, when level drops to -100 there’s a little degradation of RxQual.
    Thanks again and thanks to Ian, Pix, Brother and the others.
    Regards,
    Dell

    #62650
    Ian
    Guest

    Hello Dell,

    Have you solved your problems for Power control ?

    I would like to share some details with you as we also activated the DL PWRCTRL here.

    You can contact me at yannbrabant@gmail.com

    BR
    Ian

    #62651
    Dell
    Guest

    Hi Ian,
    thanks you reminded me. The problem remained the same at the points with low signal level. RMS_Power_Average (DL and UL) was decreased, so I put parameters mentioned in previous posts to their original values.
    Regards,
    Dell

Viewing 8 posts - 16 through 23 (of 23 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.