Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

lapd counters in eric

Viewing 15 posts - 1 through 15 (of 16 total)
  • Author
    Posts
  • #60087
    krish
    Guest

    hi ali,

    Can u tell me lapd counter and its significance in eric system?

    #60088
    raman
    Guest

    lapd counters are in LAPD object type and it’s signifance is it tells that path from BTS to BSC is affected overloaded or what by COVERLOAD counter

    #60089
    krish
    Guest

    Hi raman,

    can u tell me which counters i have to check for cell level and bsc level? can u just give its name and decription?

    and by changing lapd signalling from 16 to 32 at cdell level will get improvement in sd blocking?

    #60090
    raman
    Guest

    give command “stmotls -l LAPD” in Winfoil after aploc; command you will fidn your answers look for COVERLOAD to looked e1 wise at devices level ……….

    #60091
    krish
    Guest

    Hi raman,

    hey this counter is on bsc levelmean it will give the value of bsc level or cell level .

    if i want to check on cell level lapd loading then same one i have to use?

    and buddy i also find some counters so can u tell out of this any useful?

    CBADFRAME
    Number of received bad frames

    CTRIFRAME
    Number of transmitted LAPD information frames. The counter holds the number of frames transmitted on all links on the device, divided by ten to prevent overflow.

    CRECIFRAME

    CRETRANSM
    Number of retransmissions

    COVERLOAD
    Number of link overloads

    CLINKFAIL
    Number of link failures

    CPROCOLERR
    Number of link protocol errors

    #60092
    pridey
    Guest

    Hi.

    If i want to check on cell level lapd loading in Nokia system , then what are the commands?

    Thanks.

    #60093
    krish
    Guest

    hi raman,

    Waiting for ur reply.

    #60094
    krish
    Guest

    hi raman,

    Still waiting for ur reply.

    In trailing messege i have mentioned the lapd counters so for lapd overload coverload counter i have to check?

    And in which case coverload value shows there is lapd load?means i have to change lapd from 32 to 64?

    #60095
    Bijoy
    Guest

    Krish
    The Object type LAPD is defined per TRH device.It will give the values of the counters per TRH per BTS wise.
    Check for high values of COVERLOAD for LAPD load.
    In that case you can decrease the CONFACT.

    Pridey
    In case of Nokia,use the command ZDMF & check for alarm 2133

    Br\\
    Bijoy

    #60096
    krish
    Guest

    Hi bijoy,

    thanks buddy but can u tell me for example some value for coverload counter for 32k lapd which shows overload?

    and by that value i can go for 64 value?

    if possible plz give reply.

    #60097
    Bijoy
    Guest

    I would rather suggest COVERLOAD > 0,with no CLINKFAIL.

    #60098
    krish
    Guest

    hi,

    U mean coverload >0 means its lapd loading.so coverload should be always 0
    With no clinkfail.is it?

    #60099
    Bijoy
    Guest

    Yes dear

    #60100
    Md. Moniruzzaman
    Guest

    Hi All
    Could you please tell me LAPD performance affecting indicator threshold (Daily Resolution)

    COVERLOAD
    CBADFRAME
    CLINKFAIL

    #60101
    pix
    Guest

    hello,

    – usually, increase the lapd capacity (“confact”)

    do you know where to read those counters in the OSS ? I usually read the network QOS through a 3rd party software, but it doesn’t show those LAPD counters.
    Shall I read them in a file ? Or through AXE commands ?

Viewing 15 posts - 1 through 15 (of 16 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.