Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

drop calls

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #60010
    benaiad
    Guest

    The customers claim that the call fails often when they are in the 5th floor or higher in a building

    #60011
    positive telco
    Guest

    Is there IBS to cover indoor are?

    If not,is nearest site taller than building or not?

    Thank you

    #60012
    benaiad
    Guest

    Thanks ” positive telco “,
    can you explain me what is “lonly island”
    may be I’ve to eliminate it!

    #60013
    viju
    Guest

    multiserver issue

    #60014
    all_8
    Guest

    interference or trx faulty is one of reason of call drop

    #60015
    Mak
    Guest

    As the customer is at 5th Floor or higher floor. You have to check the following things:-

    1.Hardware issues
    2.Multiserver(How many cells are serving that area and what are the frequencies of that.
    3. It can be due to multiserver frequency interference.
    4.it can be because of overshooting cells. either you have to downtilt or define handover.

    #60016
    all_8
    Guest

    Hi all
    Thanks Mak , but benaiad you might be have to check this reasons:
    • Drop Reason, Low Signal Strength Uplink (%).
    • Drop Reason, Low Signal Strength Downlink (%).
    • Drop Reason, Bad Quality Uplink (%).
    • Drop Reason, Bad Quality Downlink (%).
    • Drop Reason, Excess TA (%).
    \BR

    #60017
    aymen
    Guest

    Hi,
    please, can you give us more details about multiserver “Mak”
    BR aymen

    #60018
    Mak
    Guest

    Could you pls tell me what is average clutter height and site height in that area.

    #60019
    Art
    Guest

    Old values: HOP = ON, HSN = 0 => Results in
    cyclic hopping (HOP is the Ericsson cell level
    parameter to enable hopping)
    New values: HOP = ON, HSN = (63 – BSIC) =>
    Results in random hopping
    The dropped call rate (DCR) decreased by
    approximately 20 percent.
    Thank you SIR Michael Pipikakis

    #60020
    broune
    Guest

    Hi,
    The following are main types of call drop:
    1. RF loss call drop (i.e. radio link fault call drop);
    2. Handover failure call drop;
    3. LAPD call drop.
    3.1.1 RF Loss Call Drop
    The RF loss call drop is shown in Fig. 3.1 1.

    Fig. 3.1 1 RF Loss Call Drop
    The RF loss call drop is divided into two parts: uplink and downlink.
    1. Downlink failure
    According to GSM specification, MS has a timer S (T100), when MS starts the call, the timer is assigned with an initial value (i..e. radio_link_timeout) that is broadcasted on BCCH.
    When MS cannot correctly decode a SACCH message (four SACCH BLOCK), S is decreased by 1; when MS correctly decodes a SACCH message, S is increased by 2.
    S will not exceed the initial value defined by radio_link_timeout. When S is zero, MS will abandon the radio resource connection and enter idle mode, and a call drop occurs.
    2. Uplink failure
    The uplink failure parameter monitored by system is link_fail.
    When the site cannot correctly decode a SACCH message, the timer in HDPC (the timer’s maximum value is defined by link_fail) is decreased by 1; when the site correctly decodes a SACCH message, the timer is increased by 2 (the timer’s value will exceed the value defined by link_fail).
    When the timers’ value is zero, the site stops transmitting downlink SACCH and starts the rr_t3109 timer (rr_t3109>T100). When T100 of MS is timeout, MS returns to idle mode and call drop occurs. The site releases the radio channel when the rr_t3109 timer is timeout. Besides, BSC has to send a Clear request message to MSC.
    Either uplink failure or downlink failure will cause stopping sending SACCH to the opposite end, and this will start the radio resource releasing procedure of the opposite end. Each time link_fail occurred on TCH will be counted as a RF_LOSSES_TCH.

    #60021
    all_8
    Guest

    Hi broune,
    may be your message has some missing words…!
    BR all

    #60022
    Mak
    Guest

    Hi Broune,

    As you have said your call drop is happening because of RLT timer expiry. Means your MS is not able to decode the Sacch frame. So your RLT counter will start and goes to 0 than after call drop happen.

    I Think it can be because of either high interference or this cell can be stand alone cell.

    #60023
    cellular
    Guest

    Hi. Can somebody plz tell me whether the T10 timer comes into play during call setup, or is it for handovers only? I want to improve the TCH Asgn Success Rate so will increasing T10 value help? It is currently set to 16 in the network.

Viewing 14 posts - 1 through 14 (of 14 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.