Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

ericsson bss commands

Viewing 15 posts - 16 through 30 (of 103 total)
  • Author
    Posts
  • #56613
    AKKI
    Guest

    CAN ANY ONE TELL ME THE COMMAND TO RESET THE RBS/BSC ALARM,TO CHECK THE ALARM HISTORY OF RBS.

    Also can you plz list out the BSC alarm and command to remove those alarms.

    your kind help will be highly appreciated.Thx

    #56614
    DaN
    Guest

    AKKI, what alarm u want to reset?
    many alarms met from transport, base station: if you reset alarm – it not reset the problem ;).

    #56615
    gsm
    Guest

    Mr. coldfire thanks a lot

    #56616
    ashish kumar
    Guest

    i want list of ericsson bss command for creating a new site and adding and digro of trx

    #56617
    DaN
    Guest

    !Internal cell definition;
    RLDEI
    !Internal cell description data;
    RLDEC
    !Cell power configuration data;
    RLCPC
    !Cell frequency configuration data;
    RLCFI
    !Cell channel control configuration data;
    RLCCC
    !Cell frequency hopping configuration data;
    !Cell channel allocation profile;
    RLCHC
    !Cell locating data;
    RLLOC
    !Cell locating urgency data;
    RLLUC
    !Cell locating disconnect data;
    RLLDC
    !Cell locating penalty data;
    RLLPC
    !Cell locating filter data;
    RLLFC
    !Cell intra-cell handover data;
    RLIHC
    !Cell BCCH system information data;
    RLSSC
    !Cell BCCH & SACCH system information data;
    RLSBC
    !Cell downlink DTX data;
    RLCXC
    !Cell dynamic MS power control data;
    RLPCC
    !Cell activation of Dynamic MS power control;
    RLPCI
    !Cell dynamic BTS power control data;
    RLBCC
    !Cell activation of BTS power control;
    RLBCI
    !Cell idle channel measurements data;
    RLIMC
    !Cell activation of ACTIVE Channel Measurements;
    RLIMI
    !Cell load sharing data;
    RLLCC
    !Cell activation of Cell Load Sharing;
    RLLCI
    !** NEIGHBOURING CELL DATA **;
    RLNRI
    RLNRC
    !** DEFINITION OF CELL MEASUREMENT FREQUENCIES **;
    RLMFC
    ! ****** MANAGED OBJECT INITIATE ******* ;
    RXMOI
    RXMOC
    !cell , tg tie
    RXTCI
    !tie to dip,dev
    RXAPI
    EXDAI
    BLODE
    ! **** EQUIPMENT IN SERVICE **** ;
    RXESI
    RXBLE
    ! ***** ACTIVATE CELL(s) ***** ;
    RLSTC
    !gprs-edge add
    RLGSI
    RLBDC

    #56618
    AKKI
    Guest

    Dear DAN,sorry for late reply.
    But i want to know the commands for
    1. To find the configuration as well as type of RBS.
    2.To reset the “AP fault” alarm
    3.To find the alarm history of the site.
    4.To reset the history alarm
    5.To reset the “size alteration” alarm
    5.To reset the “Digital path fault Supervision” Alarm
    6.To reset the “CP Fault” Alarm

    #56619
    DaN
    Guest

    AKKI,
    1. Type of RBS you can find by rxmfp:mo=rxocf-xxx, in answer printout will be ROJ of DXU; mo=rxotrx-xxx, – ROJ of tru/dtru. This info can help you identify your hardware.
    2. reset the “AP fault” alarm:
    aploc;
    alist
    acease xxx – where xxx is Alarm Identifier in alist-printout.
    But, many alarms can’t be ceased, like MIRRORED DISKS NOT REDUNDANT or General Error. You must follow OPI in Alex to resolve problem.
    3.find the alarm history of the site.
    allip;
    4. reset the history alarm
    history can’t be resetting by one command, only by resolving every alarms history will be cleared
    5.To reset the “size alteration” alarm:
    dbtsp:tab=saactions;
    saaii:sae=xxx[block=yyy],ni=zzz;
    where xxx,yyy – in answer printout from dbtsp…
    NI= old ni+15-20% (by practice)
    besides – see Alex, many sae is hardware dependent, and many is turn to another sae.
    5.To reset the “Digital path fault Supervision” Alarm
    if dip no more used, you can blocked’em :
    dtbli:dip=…;
    if else, trouble must transmit to transport department.
    6.To reset the “CP Fault” Alarm
    CP fault alarm – handling only by Alex OPI, because wrong operation may lead to CP restart or system halted. In many cases CP fault arise by hardware fault (you must change card in CP-magazine).
    this is my experience job only in GSM..
    regards

    #56620
    Andy
    Guest

    Hi Akki,

    For point 1 use also for TG configuration:
    rxcdp:mo=rxotg-xxx;
    for A bis
    rxapp:mo=rxotg-xxx;
    For point 5, you can run every 1h these commands to reset all DIP alarm:
    dtqsr:dip=all,ses2,es2,sf;
    dtqsr:dip=all,ses,es,sf;
    dtqsr:dip=all,df;
    dtqsr:dip=all,unacc,degr;
    tpqsr:sdip=0etm2,bbe,bbe2;
    tpqsr:sdip=1etm2,bbe,bbe2;
    tpqsr:sdip=2etm2,bbe,bbe2;
    tpqsr:sdip=3etm2,bbe,bbe2;
    tpqsr:sdip=4etm2,bbe,bbe2;
    tpqsr:sdip=5etm2,bbe,bbe2;
    tpqsr:sdip=5etm2,ses2,es2;
    tpqsr:sdip=4etm2,ses2,es2;
    tpqsr:sdip=3etm2,ses2,es2;
    tpqsr:sdip=2etm2,ses2,es2;
    tpqsr:sdip=1etm2,ses2,es2;
    tpqsr:sdip=0etm2,ses2,es2;
    tpqsr:sdip=0etm2,ses,es;
    tpqsr:sdip=1etm2,ses,es;
    tpqsr:sdip=2etm2,ses,es;
    tpqsr:sdip=3etm2,ses,es;
    tpqsr:sdip=4etm2,ses,es;
    tpqsr:sdip=5etm2,ses,es

    Hope they can help you.

    Andy

    #56621
    AKKI
    Guest

    Dear DAN/Andy,

    Thx for sharing these precious information.

    But i have a small doubt related to decide the RBS type.

    MO BTSSWVER
    RXOTRX-90-2 ERA-G04-R16-V01

    RU RUREVISION RUSERIALNO
    0 KRC 131 47/15 R1F X170656739

    RUPOSITION RULOGICALID
    C:0 R:C SH: 2 SL: 28 TRX TRU

    in above print out which thing i should consider with the DXU type to make decision of the RBS type.Say my dxu type is DXU-21.
    Kindly explain in detail.

    #56622
    Andy
    Guest

    Hi Akki,

    I try to find command to print the cabinet type but till now i can’t, for your help try to print the hardware inventory for all of your sites and find from the output file your cabinet type. Note that We use 23 and 31 and only DXU-23 shows cabinet type.

    Try with your DXU type and inform us the result.

    Regards

    Andy

    #56623
    Alois
    Guest

    Thanks Awii !!
    I want to know the Meaning of RDI(E1 Status)

    #56624
    DaN
    Guest

    Hi,AKKI
    as i know, dxu21 (for edge) and dxu11(old, nonedge) set up on RBS2202. KRC131 47/xxx – old transmitter for this BS (non edge), KRC131 138/xxx – with edge.
    DXU31 – on RBS 2216 cabinet,
    DXU23 – RBS2206 v2.

    #56625
    mohammed
    Guest

    Dears

    I can get internal alarms from BSM

    using bsm_export

    #56626
    DaN
    Guest

    Alois, RDI – Remote defect indication
    by practice, remote end don’t see your tx-signal

    #56627
    Saurabh
    Guest

    Hi,
    I want to know that how many alarms can be resolved by configuration end which are occuring on CF/TRX except parmanent fault.

    Thanks

Viewing 15 posts - 16 through 30 (of 103 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.