Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

cell without traffic

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • #53781
    msa
    Guest

    hi guys
    i face strange case one cell cannot carry traffic it carry handover traffic when making rlcrp
    the cell bcch=0 and it must be 1
    bcc=1 in normal case no hardware alarm appeared in the dtru the cell configuration 2/2

    #53782
    pix
    Guest

    i don’t understand “rlcrp” and “bcch=0”.

    if it means that MS can’t setup a call in this cell but can only access it with handover, then either the cell is barred or the BCCH trx is suffering bad interference or hardware failures.

    Perhaps there are some other reasons, but what you could try to do already is to lock the first TRX and see the results.

    #53783
    Narchai
    Guest

    If that cell can carry HO traffic but no TCH traffic . i suggest you to chcek Cell ID on MSC it might not define on MSC side.
    If CI already defind on MSC.
    Pls confirm this dosen’t bar.

    Good lock

    #53784
    msa
    Guest

    hi guys
    yes pix rlcrp,and bcch=0 means MS cann’t setup call
    also Narachi i check the defintion in the MSC and in the BSC for the cell i didn’t find any thing differnet all OK in the BSC and the MSC

    #53785
    msa
    Guest

    hi
    pix also i locked the first TRX no any things new still as its no traffic handover traffic only

    #53786
    pix
    Guest

    go on site, perform a drive test trace
    can you select/reselect the cell ?
    what are the values of C1 & C2 ?
    when you set up a call what happens ?
    when you send SMS ?

    please list down the message flow (layer 3)

    what is the sdcch assignment failure rate ?
    sdcch drop rate ?
    tch normal assignment failure rate ?
    call drop rate ?
    tch duration average ?
    sdcch duration average ?

    thanks,
    pix

    #53787
    Arpan
    Guest

    Hi MSA..

    Check after deleting & recreating cell_ID from MSC End..
    There must be some configration problem at MSC end thats why it in only carrying handover traffic.
    So deleting & redefining Cell ID may resolve the Issue.

    #53788
    euge
    Guest

    from wat u’ve said this’s ericsson network. Go in OSS, run mgcep on mss, run rldep on bsc. Get the cgi n both cases & compare. They s’d be same.

    #53789
    euge
    Guest

    Hi MSA,

    Did u manage?

    #53790
    MAS
    Guest

    Check the LAC in the NSS side i think it will be diffrent from the LAC in the BSS

    #53791
    GetDeendtoids
    Guest

    I need a driver for my phillips snn6500 wireless netcard
    or smc2632 wireless net card.
    I can`t make them run on linpus linux lite.

    Please help.

    Regards,
    Indewfeef

    #53792
    Ayat
    Guest

    dears

    could you explain what does mean select and reselect cell in GSM with more details

    #53793
    polka
    Guest

    Hi ayat and everybody,
    About me I suggest you to checked the CGI of the Cell, and compare it with yhe CGI on the BSC, if it’s the same try to get it’s value configure in the MSC if it is the same.

Viewing 13 posts - 1 through 13 (of 13 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.