Generic selectors
Exact matches only
Search in title
Search in content

The SDCCH assignment fail from the LU.

Viewing 15 posts - 1 through 15 (of 37 total)
  • Author
    Posts
  • #51154 Reply
    SKY
    Guest

    We want to reduce the SDCCH Assignment fail in our network. After we took a look on the cause of assignment fail,
    we found that the most was come from the Location update.
    We found in the protocol message that the failure always occurred after the AUTREQ and CICMD.

    Could you please tell me that what is the cause of SDCCH failure from the Location update?
    Thank you very much in advance. ๐Ÿ™‚

    #51155 Reply
    Pix
    Guest

    Hello Sky,

    I’m surprised you can say the problem occurs only during Location Update : during a Call Setup, the SDCCH phase is almost the same (Ciphering & authentication)

    The problem you are describing is not a SDCCH assignment failure, but it is a SDCCH drop. So it is probably linked to a radio problem, such as interference or bad coverage, which occurs on the TRX that is carrying the SDCCH timeslot.

    If the problem is only on this TRX and not on the others, then it is probably a faulty TRX.

    #51156 Reply
    Zbigniew
    Guest

    Hi Sky, what is your default value for timer T200 ? It sounds like a Layer 2 problem. Greetings Z.

    #51157 Reply
    SKY
    Guest

    Hello Zbigniew,

    Thanks for your recommend.

    We are using the T200=300ms corresponds to Abis terrestrial link. (in Alcatel have only 2 choices, Terrestrial=300ms and Satellite=1000ms.)

    More information and more question about this problem.

    We found the time after the CLUPD(send from BSC to MSC) before the CLCMD(send from the MSC to the BSC has the cause value=call control) is equal about 11s.

    From this it look like the time out behavier.

    Could anyone please tell me that which timer should it be?

    #51158 Reply
    Pix
    Guest

    i don’t really want to disturb anymore… ๐Ÿ™‚

    #51159 Reply
    SKY
    Guest

    Why not, Pix??? Please!!! ๐Ÿ™‚

    #51160 Reply
    Zbigniew
    Guest

    Hi Sky, I recommend to set the timer T200 to 1.000 ms. We noticed the same problem in Nokia and Siemens BSS. Greetings Z.

    #51161 Reply
    NarChai
    Guest

    Motorola BSS?
    it might be “Phantom RACH”

    #51162 Reply
    SKY
    Guest

    We found that the 11-12s time out is the T3109 which is related to the Radio link timeout.

    So it probably linked to the radio problem like Pix said.

    We are investigating and finding out the solution.

    Any recommend are welcome!!! ๐Ÿ™‚

    BRs,

    #51163 Reply
    Dariush
    Guest

    Can You tell me is this site border site? if yes please check the bsc borders and try to decrease coverage for this site to have less LU In your networks.

    #51164 Reply
    sunny
    Guest

    Try increase the CRH( Cell reselection Hysteris) on the border cells . This will decreasse the ping pong around the LA Border and so the sdcch faiures will decrease

    #51165 Reply
    Zaki Ryne
    Guest

    Dear all,

    I am working as a network performance team Engineer. During drive test we have 2 cell phones adjusted which call one another(master & slave phone) continuously. But when they crosses the location border, the call drops.

    Can anybody give me a suggestion what actually happens in the border? Why do they always drop?

    #51166 Reply
    Pix
    Guest

    Have you looked at the messages logged in the drive test (layer 3)
    – what happens just before the drop ?
    – what about qoS statistics in serving and target cells ? do you notice something in terms of handover failures or call drops ?

    i would suspect that the two location areas are located in different MSC’s, right ?

    you could check neighbour definition and LAC definition in the different MSCs (can’t tell you more than this, you must check with NSS engineers)

    you can also ensure that both cells are using the same ciphering algorithms, as it can lead to a drop when switching ciphering in dedicated mode (as I experienced, but it might not be true with every vendor !)

    if the cells are from same MSC, but different BSC, then there is probably something you need to investigate on the A interface.

    Altogether, you can investigate further with detailed QoS indicators and/or A interface traces, and simply have a look to your layer 3 messages in the drive test.

    Regards,
    pix

    #51167 Reply
    Zaki Ryne
    Guest

    Dear Pix,

    Thanks for the suggestion. I will try them out.

    Best regards

    Zaki

    #51168 Reply
    Alexx
    Guest

    Dear all,
    I work with BSS Alcatel. We have a serious problem with Immediate Assignment: for 20% of cells it`s ~ 85-90%.The problem connects to counter MC149 – expired T3101 (3 sec), i.e. within 3 sec MS doesn`t acknowledge occupation of SDCCH. We have changed BCCH/BSIC to chek the version with Phantom RACH and BCCH-interference, have changed all equipment in the cell (trxs & ANc) but – without any results ๐Ÿ™
    Do anybody have similar problem?

Viewing 15 posts - 1 through 15 (of 37 total)
Reply To: Reply #51164 in The SDCCH assignment fail from the LU.
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">