Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

BTS TRX

Viewing 15 posts - 61 through 75 (of 78 total)
  • Author
    Posts
  • #50964
    Zainab Khan
    Guest

    can anyone please tell me how to improve Minutes per Drop MPD in NOkia BSC..!!

    #50965
    Daud Mohttat
    Guest

    dears

    we r lossing traffic after increasing the capacity in BTS-6000 family. (BTS-6102) do u have experience in this regard??

    #50966
    Sandeep Jain
    Guest

    How many erlangs in one TRX

    #50967
    HUMAYUN KHAN
    Guest

    how many channels can one TRX carry?
    pls clerify if any one has the khowledge about it.and in how many time slots will one channel be broken?

    #50968
    Mayur R Neelavar
    Guest

    I need to know how many Erlang 1 TRX can carry at full rate. I am not a telecom enginner and my understanding is limited. But I believe the Erlang carried by a TRX can increase if one applies half rate in an percentage. I need to know what the Erlang a TRX can carry at full rate.

    Thanks for the help!! Cheers..

    #50969
    pix
    Guest

    hi,

    One cell can be configured with 1 to 12 TRX (usually).

    The more TRX you put in one cell, the higher the capacity (it’s non-linear)

    With only one TRX, you can have max 7 channels for voice.

    Go there :
    http://www.erlang.com/calculator/erlb/

    Select BHT as “unknown”
    Blocking = 0.02(= 2%)
    Lines = 7 (7 channels)

    click on Calc.
    capacity of 1 TRX = 2.9erlangs (full rate)

    In halfrate, you can have 14 channels –> 8.2 erlangs.

    The capacity in erlangs depends on the acceptable blocking rate. By default 2%. Most operators today are choosing lower blocking (1% or 0.05%).

    Regards
    pix

    #50970
    Sunkanmi
    Guest

    Hello everyone. Please I need to know how to calculate the maximum number of TRX that can be configured in a cell. Given that the TCH will use 1*3 frequency reside for arfcn of 45 -80, while BCCH use 81-94. Bandwidth is 10Mhz.
    Thank you.

    #50971
    pix
    Guest

    hello,

    with 35 ARFCN for the TRX TCH, and a RF Load of 30% on a 1×3 pattern.

    –> 35/3 = 11.6666 arfcn MA-LIST per sector (let’s round up to 11, so you can keep “joker frfequencies”.)

    30%*11 = 3.3 TRX ‘TCH’ / SECTOR

    so basically, you can easily have 1+3 TRX per sector (1 bcch + 3 tch), with good radio quality.

    By pushing radio quality and taking into account a traffic < 100% capacity at busy hour, I think you are safe to push the capacity to 1+4 TRX per Sector. That's a radio load of 36% which is still very acceptable. Maybe you'll see some qos degradation @ the busy hour. In such case, do some downtilting to reduce overlaps, and increase HR usage. regards, pix

    #50972
    Sunkanmi
    Guest

    Hi Pix,I Thank u for your reply. Please I still need further clarifications because am fresh in RF planning.
    How do i calculate the RF load for each reuse pattern?
    Thanks

    #50973
    Adil khan
    Guest

    Humyoon khan
    In one E1 there is 16 trx hop u know that
    and in 1 trx there id 8 chaneels in 8 channels there are 2 chanells for TX and RX remaing ^ chanell for user

    #50974
    SHAHID TANVEER
    Guest

    A Trx have 8 timeslots and 1 timeslot for 1 user
    1-Trx = 8 Timeslots
    1-Timeslot = 1 user

    #50975
    RAMNARAYAN SONI
    Guest

    WHAT IS dual Half rate & capacity in er-lang.

    what is LLC Throughput & user Throughput & difference.

    definition of logical & physical or type & use.

    #50976
    vijay
    Guest

    Plz…..
    Tell me, how consider the frequency for one TRX

    #50977
    Jamshid Ali
    Guest

    Plz share me detail of of the following Q…
    1: How many Trx in 1 sector of BTS,
    2: Difference Between RSCP & RxLeve, why RSCP level is Less than Rxleve.

    #50978
    BHANU
    Guest

    HOW MANY TRX ARE THERE IN A SINGLE MODULE

Viewing 15 posts - 61 through 75 (of 78 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.