Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

NOKIA Base Station Frequency Reference

Viewing 15 posts - 1 through 15 (of 25 total)
  • Author
    Posts
  • #49457
    DAC Drifter
    Guest

    Nokia Ultrasite

    BCF OPERATION DEGRADED
    02 01 07 96 00 00 : Difference between PCM and base station frequency reference.

    The above alarm condition has been discussed here before but a resolution was never found. Does anyone know if this is being produced at the cell or at the BSC level. It does not appear to be service effecting.

    Have replaced BOIA, FXC, Abis cables connections, span extentions cables and had telco swap SMJK.

    Any help would be much appreciated!

    #49458
    Sharique
    Guest

    Please check the DAC Value , if you have Frequency counter , then Put 13MHZ, DAC value must be 2040.
    Ih not frequency coounter then put 2140.
    my mail ID is
    mdsharique@rediffmail.com

    #49459
    DAC_Drifter
    Guest

    Thanks for your reply Sharique.

    If I don’t have ready access to a frequency counter would I set the DAC value to 2140 or 2040?

    #49460
    Rahis Khan
    Guest

    Even during setting the DAC value
    make sure that the BTS OMU link is disabled even check if there is alarm in ultrasite bts hub manager of Frequency error if this alarm is exsisting then check ur synchronisation settings .

    #49461
    DAC Drifter
    Guest

    The most difficult problem with this is that the alarm is very hard to catch. I’ve never seen a frequency error while using BTS Hub Manager.The only way that I have seen it is through MML while checking the sites alarm history.

    ZEOH:YEAR-MM-DD:BCF=XXX;

    It always clears on its own and is never present for more then a few minutes. Mostly it comes in during the middle of the night. It does not appear to be service effecting.

    #49462
    patrick.fr
    Guest

    there is no solution.

    Statistic of your BTS is correct, everything is correct, you have changed every card (BOIA, FXC, 13Mhz is ok, …) ….and you have still this alarm.

    I have a same problem and now i don’t care because my site is working and all good work.

    I think that problem is quality of PCM 2Mbits. But where and why? i don’t know.

    check your ET with => ZYMO:ETxx;

    #49463
    Gabriel
    Guest

    Try swap T1 or ET. If you have a second cabinet that doesn’t have this kind of alarm, swap it’s ET to the cabinet that have this alarm. You can also try swapping the T1. This will need the assistance of Switch. In this way, you will be able to isolate if the issue is with the ET, T1 or BSC clocking or whatever. Just try!

    #49464
    DAC_Drifter
    Guest

    Well, after many months of alarm free conditions our:

    “ALARM 7601 Difference between PCM and base station frequency reference” alarm has returned for the season. As it appears the alarm returned the night of the National Weather Forecasts’ First Official Frost Warning of the season. Once the temperature went above 32 F the alarm cleared. It returned 2 nights later when the second official frost warning came in.

    #49465
    ol
    Guest

    what kind of transmission equipment do you use? Is it ericsson minilink?

    #49466
    gyanendra
    Guest

    dear dac drifter,

    what is the media that you are using for the BTS..I mean whether it is PDH or SDH..OFC or MW & like that. Also what is the status of your BSC clock? Give o/p of ZDRI:; & DAC value of the BCF for which the alarm is reported.

    #49467
    Ankit Singhal
    Guest

    What is the purpose of setting a DAC value in Nokia BTS??? What is the appropriate DAC value on should enter???? How one can clear the DAC alarm if there are flicks on the ET????

    #49468
    Ravindra Pratap Singh
    Guest

    How can we clear 7601 Alarm?
    Is’t clear?

    #49469
    apur
    Guest

    What is the Full form of DAC value?

    #49470
    Ashish kumar
    Guest

    How will alarms 7604,7601,7745,7704,7606 will effect the RADIO kpi? can anyone explain that for each of the above alarms……..THNX

    #49471
    kamal kotecha
    Guest

    Apurbhai,

    Dac STands for Digital to Analog Converter..

    For measuring Abis purity,BTS continuously monitor value & adjust DAC word if required..

Viewing 15 posts - 1 through 15 (of 25 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.