Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

RX Diversity Alarm

Viewing 15 posts - 16 through 30 (of 64 total)
  • Author
    Posts
  • #49063
    Hamanta Mech
    Guest

    How can I cease the rx divercity lost alarm.
    ( I had check the antenna to Bts feeder/jumper connections, replace the Tx-Rx cable. reinstall the IDB,but still the alarm exist. )

    #49064
    oleg
    Guest

    to aman
    tell me why the diversity alarms are arrise in two sectors…

    u probably have X-connection of RX feeders between two sectors.

    #49065
    OLeg
    Guest

    Fault name RX diversity lost
    Description The imbalance in signal strength between the receiver A- and B-side is
    supervised on a TRU basis. The fault arises when one or several TRUs have
    reported a signal strength imbalance of at least 12 dB during 50 minutes.
    This indicates that an RX path to one or several TRUs is faulty. The
    receiver sensitivity for these TRUs is reduced by about 3.5 dB. Note: This
    fault is not raised if one of the faults SO CF I2A:7 (RXDA), SO CF I2A:11
    (TMA current), SO CF I2A:34 (TMA voltage) or SO CF I2A:39 (RX cable)
    is active.
    Action Enable the diversity supervision monitor in OMT for each TRU, to find out
    which TRUs are affected and which side (A or B) is faulty. The diversity
    supervision measurements are only taken every 5 minutes so it takes some
    time to notice changes. The measurements give signal strength imbalance
    (SSI, expressed in dB) on each TS. The SSI is equal to RX signal A-side
    minus B-side so positive values indicate that A-side is better and vice-versa.
    Check that all cables on RX-path are properly connected (including HLin/
    HLout). Also check the antennas. If several cells are affected then maybe
    two RX feeders have been switched. If only one TRU is affected, then
    check RX cable between TRU and CDU. Try moving TRUs, CDUs and
    cables in the cabinet to see if the fault follows the unit(s).

    #49066
    michael
    Guest

    i had an alar in a 2106 ericsson rbs or rx path lost on b reciver side and i already change the feeders jumper cables antenna and cdu rf conectorrs an the alarm goes off and after a coople hours comes back can somebody help me

    #49067
    Oleg
    Guest

    To Michael:

    The fault arises when one or several TRUs have
    reported a signal strength imbalance of at least 12 dB during 50 minutes.

    Use OMT/Maitenance/monitor/Diversity supervision meas/… check all TRUs (You should wait 5-10 min during monitoring). Select TRU with worse SSI(Side A-B), try to exchenge DTRU betwin cells, perfom monitoring again, if fault (bad SSI)goes with DTRU – install a new one, ather case – try to replase CXU. Monitor again.

    #49068
    prince
    Guest

    Frequency interference can also cause Rx diversity alarms so please check your frequencies.

    #49069
    Bijoy
    Guest

    Hi Prince
    Please elaborate how this could happen??I’m really curious!!!

    Br\\
    Bijoy

    #49070
    Jim
    Guest

    Does Anyone if you can set up 2106 BTS with LNAs without the use of the TMA Card?

    #49071
    hari
    Guest

    I need to know the value rx path imbalance.the value is in between 12 to -12 db or else only +ve values or -ve values

    #49072
    Ratan Deep
    Guest

    Is DRU faulty may lead to
    VSWR.

    #49073
    abdul nkrumbih
    Guest

    I get the rx diversity lost on B receiver side when TMA is activated in rbs 2106
    How can I go about to solve the problem.Please help.

    Again when calling from the site,called part can hear me but I cant hear fro him.

    #49074
    Rex
    Guest

    Hi Abdul,
    in cases when you can’t hear called party the problem is his Uplink. Check connections with TMA whether they are wrong connected or change TMA.
    Regards,
    Rex

    #49075
    abdul nkrumbih
    Guest

    What is the problem actuaaly,some sites have rx diversity lost but still people communicate while in othersites it is vice versa.
    Can anyone clearly elaborate more?

    #49076
    Jason
    Guest

    Hi All;
    I seem to be having a similar issue with the ‘RX path imbalance’ alarm. I need some assistance also. I don’t believe that this is a hardware issue because it seems to be randomly coming and going on our 2106 sites.

    My First thought:
    I am wondering if we have a parameter problem. Defining this alarm I can adjust:
    Class 1 Alarm(dB): mine is set to “Off”
    Class 2 Alarm(dB): mine is set to 6.0 the default
    Supervision Window Time(minutes): mine is set to 1440 the default
    Minimum Number of Samples: mine is set to 7000 the default.

    I know if I set the Class 2 Fault Limit to “Off” I will get rid of the alarm, but that will not solve anything.

    So I have thought about tuning these parms, but I am not sure where to start with these.

    Second Thought:
    In the RBS OMT I have the ability to “Define the loss” Currently we have no TMA’s and our value for this is set to “0”. The documentation I found on this said we should set this to “0” for non-tma configurations.

    Please help with any thoughts or ideas. Thanks.

    #49077
    abdul nkrumbih
    Guest

    I have noted the following scenario:
    One leg was affected by VSWR and thus cause one dtru to be out of service.

    After measurement of distance to fault using site master i found there was water inside the polyphaser connected between feeder and jumper.

    However i was not able to dry he polyphaser due to its shape,thus i decided to bypass the polyphaser.
    when that is done you also get the rx diversity lost on that dtru.
    when the plyphaser is reconnected the diversity alarm disappears.
    We may start frm there to re-establish a complete sln towards the diversity lost alarms.
    Any one can volunteer

Viewing 15 posts - 16 through 30 (of 64 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.