Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Paging Success Rate

Viewing 15 posts - 16 through 30 (of 88 total)
  • Author
    Posts
  • #48692
    Aman
    Guest

    dear, how can we improve paging success rate in E/// BSC? what paging parameters should we check in BSC?

    #48693
    Bijoy
    Guest

    Aman
    Kindly let me know the following parameters.
    BSC/BTS Parameters
    1.MFRMS
    2.AGBLK
    3.BCCHTYPE
    4.T3212
    5.ATT
    6.MAXRET
    7.CRH
    8.RAEPP

    MSC/MSS Parameters
    1.BTDM
    2.GTDM
    3.TDD
    4.PAGNUMBERLA
    5.PAGTIMEFRST1LA
    6.PAGETIMEFRSTGLOB
    7.PAGEREP1LA
    8.PAGEREPGLOB
    9.PAGTIMEREP1LA
    10.PAGTIMEREPGLOB

    Br\\
    Bijoy

    #48694
    sewashi
    Guest

    how about in nokia? what are the parameters involved?

    #48695
    Bijoy
    Guest

    Hi Sewashi
    In Nokia
    BTS Parameters
    1.MFR
    2.AG
    3.MBCCH or MBCCHC
    4.PER
    5.ATT
    6.RET
    7.HYS

    Let me know if you need MSC/MSS parameters too

    Br\\
    Bijoy

    #48696
    sewashi
    Guest

    thanks bijoy for the parameters. can i also have the msc parameters? tnx..

    also i would like to ask, is sdcch congestion/blocking related to paging success rate? kindly explain.

    #48697
    Bijoy
    Guest

    As you wish
    Here we go
    MSC Parameters
    1.Repaging_Interval
    2.Number_of_Repaging_Attempts
    3.PAGING Method
    VLR Parameters
    1.TMSI PAGE REPETITION IN MT CALL
    2.LIMIT FOR SIMULTANEOUS SEARCHES
    3.SEARCH RESPONSE WAITING TIME
    4.TMSI PAGE REPETITION IN MT SMS
    5.TMSI Used

    Yes,SDCCH Blocking may affect the Paging Success Rate

    Br\\
    Bijoy

    #48698
    sewashi
    Guest

    thanks bijoy for the parameters.

    but can you explain how it is related to sdcch blocking? im a little bit confused. is it rach that is being used as a reply to a paging message?

    #48699
    Bijoy
    Guest

    Ok
    Let me try.
    In response to paging,RACH(Channel request) will be sent by the MS to the BTS with the CM service Type.In response to RACH,BSC will ask to BTS to activate a channel(usually SDCCH).Now,if there is no usable/free SDCCH available,BTS will reply with Channel NACK/Immediate Assignment reject.Now,since call set-up indication is not being sent to the MSC,so no paging response.Hence,PSR goes down.

    #48700
    Ameen
    Guest

    Hi Bijoy,

    Thanks for the information, however just wanted to point out that in Paging Scenario, “CM Serv Request” is not sent. Instead, when SDCCH is established, MS sends “Paging Response” to the network.

    CM Serv Request (4 types) are only in Mobile Originated scenarios.

    Moreover, RACH contains only Cause Values (for whichever service required), where CM Serv Req message is a layer 3 message which is only sent when SDCCH is established.

    Regards,
    Ameen

    #48701
    Bijoy
    Guest

    Thanks Ameen for the slight correction.
    But again,as you have written “in Paging Scenario, “CM Serv Request” is not sent” is not correct.You contradicted yourself in your post itself

    Br\\
    Bijoy

    #48702
    vijay
    Guest

    How to improve psr in zte MSC & BSC?

    #48703
    kuljit
    Guest

    Are these parameters are also has to seen in ericcson system to improve PSR

    #48704
    Preethi
    Guest

    Hi Bijoy,

    In nokia BSC, can you pl provide explanation of the BTS parameters which will improve PSR alongiwith full for

    Thanks.
    Regds’ Preethi

    #48705
    Muyiwa Adedayo
    Guest

    Hello all,
    I am just coming into the forum.
    i am an RF engineer with MTNN and hope to fully be part of the house shortest time.

    #48706
    Bijoy
    Guest

    Hi Preethi.
    Please see my post down below for the paging parameters.
    Please go through NED for details.Do ask for any doubt.

    Br\\
    Bijoy

Viewing 15 posts - 16 through 30 (of 88 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.