- This topic has 11 replies, 1 voice, and was last updated 13 years, 3 months ago by Nur.
19th June 2007 at 09:27 #47835akefaGuest
if I have the following:
1) 2 sdcch/8
2) 4.17 sdcch traffic
3) 104 sdcch availability (adaptive configuration)
4) 18% sdcch conjestion !!
could any body justify the congestion? any possible scinario?
akefa21st June 2007 at 04:56 #47836NKGuest
It can be due to phantom RACH. try to change timer T3101 to lower value.
NK21st June 2007 at 13:31 #47837akefaGuest
regarding the timer you mentioned, is it in Ericsson? coul you plz justify why decreasing this timer may solve the problem.22nd June 2007 at 04:06 #47838NKGuest
I am using Siemens. Phantom RACH is one of the reasons for SDCCH congestion. When BSC gives immediate Assignment message for SDCCH via RACH, BSC runs T3101. If timer the dedicated channel is not
established before T3101 expires, the allocated channel is released.
This scenario can e.g. occur if noise on the radio is decoded as
RACH access (“phantom RACH”) by mistake.
If this is a case, setting a long time for it means long time to wait for SDCCH response from MS which does not exist. This gives lower Traffic but SDCCH congestion.
If this a case, I hope decreasing it will solve the problem.
NK22nd June 2007 at 09:19 #47839akefaGuest
It is clear, thank you. Your info was clear like the sun, quite like the moon
I will try to play with this timer and see the effects. I will call this timer the layers discover (phantom RACH are big layers 🙂
I already made a soft reset for the site and every thing back to normal for the last 3 days. Therefore, the phantom RACH 🙂 here maybe due to hardware.24th June 2007 at 08:41 #47840akefaGuest
Actually i have been told that i can not play with this timer, it is fixed !!
(ericsson)25th June 2007 at 19:51 #47841akefaGuest
Hi Pix and NK
t3101 is the timer of IMMEDIATE CHANNEL ASSIGMENT so is not related to the sdcch ! immediate assignment means the MS’s will be assigned a signaling channel directly from TCH, and hence the word “direct” came. i am confused because you are talking about sdcch. plz you can read the definition of the immediate assignment or t3101 again !
once you answer, I have more to say regarding the issue.
take care27th June 2007 at 03:50 #47842NKGuest
Immediate assignment means SDCCH if assignment type is “Early Assignment(EA)” type and TCH if assignment type is “Very Early Assignment(VEA)”. Most of the opeartor use “Early Assignment” so that TCH can effectively use. I hope that your type is EA.
If timer T3101 is fixed in your network, I think it is optimized value. SDCCH congestion may be due to another reason.
NK15th October 2007 at 09:21 #47843TounsiGuest
Please anyone can tell me the difference between immediate assignment and normal assignment ?
Also, Is there other kinds of assignment ?
Regards15th October 2007 at 12:47 #47844pixGuest
the immediate assignment is the message sent from BSC -> BTS and BTS -> MS during a normal assignment. This message is sent on AGCH, and describe the physical address of the SDCCH subchannel that is going to welcome the call. Once the MS gets this info, it will move to this SDCCH subchannel.
A normal assignment means a “call setup”, in opposite to handover assignment. It is also written “NA”.
Regards,18th October 2007 at 11:47 #47845RamiGuest
Check RACH Busy Threshold, MAX RETRANS, LAC border
Good Luck18th October 2007 at 19:25 #47846NurGuest
Dip is not comming into service
problem is below,dip is showing abl & rdi fault.
Could anybody advice me what should i do..