Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

tch access failure,SDCCH drop

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • #47244
    senarist
    Guest

    hi all
    my questions that what is tch access failure and what is different from sdcch drop,also How can understand it that this tch access failure or sdcch drop.
    thank you for your advice…if you have any document shared with me ı will happy.(hsy616734@yahoo.com)

    #47245
    oharazu
    Guest

    TCH Access is ability of MS to use TCH. It relates to TCH Blocking, HO Blocking, and Call Setup Success Rate.

    For instance a SDCCH drop can be caused to interference, low coverage (uplink, downlink) settings of bss parameters, or an Abis failure.

    As for SDCCH drop, user side will experience the call is try to connect yet not complete and MS return to normal. As SMS, the SMS won’t be sent out after certain while connected/sending.

    For situation having high TCH Access FAilure Rate, when u make call, after “connecting” you will get call block/reject~ “network busy”.

    For situation having high SD drop, you get immediate reject after press call and connecting.

    Situation can be harder if the site facing both TCH Access Failure and SDCCH drop.

    #47246
    senarist
    Guest

    Oharazu;
    ı know it and ı have to agree with you but ı want know that when time start (for example immediate assigment tch then access tch or not)so when time start it and finish SD drop, When time start it tch access failure which signal together or system information data seem that its tch access failure,how can ı say… and counters when its percive this..thanks all

    #47247
    Pix
    Guest

    Senarist,

    The SDCCH Drop occurs during the SDCCH pahse, which is the phase when the MS and the MSC communicates transparently about ciphering, authentification, etc…

    So, the SDCCH phase ends when the MSC sends the “ASSIGNMENT REQUEST” to the BSC (it is not a transparent message anymore).

    Then starts the TCH ASSIGNMENT phase, until the message ASSIGNMENT COMPLETE is sent from MS to MSC.

    Regards,

    #47248
    oharazu
    Guest

    yes, SD Drop counter is located before ASSIGNMENT COMPLETE msgs. After that would be the TCH counters.

    more info, for high traffic BH, SD access rate is high and radio stability is much crutial at this moment. it is fast access within short time period.

    optimising SD drop could be much more difficult than expected. start with RF signal strenght.

    #47249
    Mohit Dave
    Guest

    Hi can any one explain what is the different between TCH Assignment & TCH Seizure??

    #47250
    Suhail Mlik
    Guest

    Hi Mohit.
    TCH assignment is from BTS end to MS while siezure releates ability Of MS to hold that TCH

    #47251
    Mohammad Helal
    Guest

    what is the meanning of paging per second?

    #47252
    Jeremy
    Guest

    Hello,
    what is the difference between TCH BLOCKING RATE and TCH LOSS RATE?
    Best Regards

    #47253
    dassougui tadjassir oumar
    Guest

    after we see the statistic repportement from performence i want to konw ,how the opimization adding the capacity or power of the cell

    #47254
    Swamy
    Guest

    What is TCH Norm Seizures in NSN?

    #47255
    123
    Guest

    tch_norm_seiz does not mean that the MS is on TCH. It means that TCH has been successfully seized. Some mobiles never appear to the TCH because:
    • the call is cleared by the user (probability is higher if call setup takes
    a long time, and thus DR and queuing can increase this share) or
    • the mobile fails or
    • something else goes wrong.

Viewing 12 posts - 1 through 12 (of 12 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.