Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Problem with MW link

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • #46953
    Winet
    Guest

    Hello,

    I have a link made with 0,6m ericsson antennas and after panning it appear that on one side of the link level of received signal strength is -40dBm but on the other side it is -70dBm. Any ideas why is it like that and how to fix it?

    #46954
    tarun nagpal
    Guest

    hi , firstly check that whether u r using same polarization or not . this could a big factor u r getting -30 db differnce

    #46955
    emre
    Guest

    are you sure same tx power is used both 2 side

    #46956
    Peter (NL)
    Guest

    Did you allign the link? Because it is also a possibility that one of the OU’s is in a sidebeam. Try to re-allign the link.

    Grtz,
    Peter

    #46957
    eng. mis
    Guest

    i think if you check all above possible reasons the radio is faulty try to change it

    #46958
    hassan
    Guest

    You know , you need to re-align the link in both sides again

    #46959
    ali
    Guest

    hi winet
    pls check the small hole in side the radio is open r not smtime that is closed so u have to move it & make with another hole stright so i think then u can get the require points & also check there is nothing interfarence b/w the two sites

    #46960
    umer
    Guest

    Hi Winet,
    in order to rectify the problem perform following step

    check what sort of alarm are on equhipment by getting its log
    this will help you to now what sort of alarms appear on link
    Other wise you perform below mention steps
    Check Polarization on both end
    check TX power on both end

    Chehck link alignment

    i hope this will solve your problem

    #46961
    Winet
    Guest

    Hello, I checked polaryztion, cables, Tx power and re-aligned the link. Nothing has helped. I’m going to replace ODU-s on both sides…
    BY the way, Is there any way to check IF radio transmitter is working? In ericsson i can simply do a loop on the ODU and check Rx signal. But I have a link 1+0 made on Nokia 23Ghz antennas , and on one of the end there is no Rx level shown. I replaced the radio radio cause i thought that maybe it is receiver fault, but it didnt help. Other possibility is that on second radio transmitter is faulty. And i wonder if there is any way to do it? Link is made on FIU-s. Thx for sugestions.

    #46962
    Patrick.fr
    Guest

    Is ODU integraded or separated?

    If separated, the wave guide can be broken?

    Bad polarity (H or V)in one side can be lost 20db.

    On your FIU Nokia, LED FB are Green? fix or Twinkling?

    #46963
    Winet
    Guest

    For those who are intrested.. In ericsson there wasd a faulty ODU – something wrong with reciver, this is why Rx lewvel was about 30DBm lower there (After we exchange ODU everythimg was working ok).

    #46964
    Pankaj
    Guest

    we Installed Traffic Noda Ericsson SDH. Problem in this Link are Fluctuated, every thing is clear,error rate problem is also Generated but this problem is solved but fluctuated problem is present.

    #46965
    Njari
    Guest

    when aligning a link we use a meter which shows us the levels in voltage how are this volts converted into db which we see in the computer

Viewing 13 posts - 1 through 13 (of 13 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.