- This topic has 21 replies, 1 voice, and was last updated 12 years ago by NA.
-
AuthorPosts
-
2nd February 2007 at 08:17 #46560Geet MukhraGuest
hi u asked u about clearence of fiu 19 for that u have to run the script tool .so that u can clear the datebase in the fiu 19
2nd February 2007 at 15:06 #46561patrickGuestwhich database?
The best reset is:
setting FIU
search button HARDWARE reset in one Tab.
Click ONYour FIU reset => So, you Cut traffic.
4th February 2007 at 08:32 #46562YellaiahGuestHi Geet & Patrick,
Use the following steps to clear the DATA BASE FULL Alarams
i.e.Run VIEW in the SCRIPT TOOL( TOOLS)
and give following commands for NE , IDU and ODU,for NE 6,2,1,1, Excute it
For IDU and ODUs K:13,1 excute it.
regards
Yellaiah
yellaiah.gunti@gmail.com7th February 2007 at 10:26 #46563Geet MukhraGuestHi Yellaiah
Thanx but is it traffic affecting ??8th February 2007 at 12:28 #46564Geet MukhraGuestCan any one tell me pin configuration for Q1 managment in FIU 19 and FIU 19E….
8th February 2007 at 16:12 #46565patrickGuestQ1 you can supervise FIU by BTS ultrasite or citytalk.
ZQUS:BCF=XX; to see TRANS card (FXC ET1/T1)
ZQWL; to see all adress Q1
ZQWA to add adress
You can create adress with your number BCF.
You must make an adress on your FIU and configure in FIU setting.
example:
ZQUS:BCF=xx:DMR=xx;=> you can see alarm, rssi, name, …, change setting, … on your FIU with MML.
9th February 2007 at 12:01 #46566Geet MukhraGuestThanx patrick but i need Q1 pin configurations so that i can connect FIU and ULTRA BTS at the site through Q1 Managment……
9th February 2007 at 13:04 #46567patrickGuestOn Q1 BTS DB9 use pin 1, 6, 5, 9
I don’t remember where is TX and RX but you must crusader TX and RX between Q1 DB9 ULTRA and Q1 FIU
After, you must configure FIU Q1 with Flexihoppermanager: adress, speed, name, …
14th February 2007 at 19:06 #46568RICGuestDoes anybody know why FXCRRI in XXXXHubs sometime lose CC Bank and Sync settings? Also why does Ultrasite lose TRE and only Power reset can help only Is it possible restore Hub without traffic cut
17th February 2007 at 15:59 #46569patrickGuestRIC – 14 Feb 2007
Change BOIA or FXCRRI because it is not a normal functioning.
I have already had the same problem but i can explain why.
This problem must be rare.
20th February 2007 at 08:20 #46570RICGuestI noticed that fault never repeat at the same XXXHub and with swapped RRI or BOI. These units after installation in other places are working enough stable.
12th June 2010 at 05:15 #46571NAGuestHi all!
i’ve a problem using EPIU unit in FIU19E.
so its a question, how we can use EPIU unit for making visibility of FIU to NMS (Q1 connectivity is known).
I need full steps and configuration.
12th June 2010 at 10:41 #46572KJBGuestHi Ric & Patrrik,
I have noticed this problem due to Faulty RRI,Some time Conteminated Pins of RRI back plan.
Some time Hub restored after Soft RESET given to FXCRRI.
Thx
KJ
13th December 2010 at 14:42 #46573ARUN KUMAR MISHRAGuestWHAT IS FULL FORM OF FIU .
24th December 2010 at 17:26 #46574FawadGuestWhat is the role of TX power.
Why we give TX power?
-
AuthorPosts
- The forum ‘Telecom Design’ is closed to new topics and replies.