- This topic is empty.
8th August 2010 at 04:48 #44522SHAILENDRAGuest
WHAT IS RSSI?9th August 2010 at 19:04 #44523korgiGuest
Meaning of RSSI – “Receive Signal Strength Indicator”, is a circuit to measure the strength of an incoming signal.
The Received Signal Code Power is the received power on one DPCH, PRACH or PUSCH code after de-spreading, defined on the pilot symbols.29th September 2010 at 14:22 #44524FjennGuest
It appears that RSCP and EC/IO are pertinent to outdoor macro cell sites since it has to do with actual ‘cells’. Does it affect, or should it be a design consideration, for indoor DAS where all antennas retransmit the same ‘cell site’ (in this case a BTS) through the building?2nd October 2010 at 11:09 #44525ganesh singh tomarGuest
can any one tell me the what is Ec/N0 in Brief with Example19th October 2010 at 07:10 #44526TanveerGuest
If we have measurements for the Received Total Wideband Power (RTWP) and Ec/No at the UTRAN cell then could we use that to calculate RSCP ? i.e. RSCP=RTWP+Ec/No3rd November 2010 at 10:56 #44527girishGuest
can any one tell me the parametres in 3g10th November 2010 at 04:25 #44528Anshu AroraGuest
All Rf condition ok and no alram on the site then rscp bad how can i improve the rscp and what parameter i will checked16th November 2010 at 08:02 #44529Prashant ShriwastavaGuest
Question–All Rf condition ok and no alram on the site then rscp bad how can i improve the rscp and what parameter i will checked.
Answer–Change the project or change the Node-B.9th December 2010 at 09:13 #44530santosh nayakGuest
what is rscp in 3g and plz tell me all the parameter in 3g we used3rd January 2011 at 09:45 #44531Zulfiquar AhmedGuest
RSSI= RSCP-Ec/Io13th January 2011 at 08:39 #44532prabhat kumar patraGuest
what relation between Ec/No & Ec/Io?27th January 2011 at 08:42 #44533hari narayanGuest
can anybody help me getting GOOD NOTES ON 3G PARAMETERS AND THEIR RESPECTIVE RANGES .PLZ MAIL ME AT email@example.com January 2011 at 10:38 #44534santosh nayakGuest
what we will see in layer 3 message
while location update?2nd February 2011 at 04:02 #44535Zulfiquar AhmedGuest
RSCP is more or less similar to RX level of 2G,
Ec/Io to C/I
The range of RSCP is similar to RX level but the range of Ec/Io is from 0 to -30. Greater the Value better is the quality. The value is -ve as the Io includes Iown, I others and noise.(I=interferece).
Note: Unlike in GSM if u miss defining any neighbor site as neighbor there will be a call drop. This is because we are operating the whole Network on one single frequency and missing neighbor of that same frequency is considered as interfernce and the Ec/Io value becomes poor and thus leads to a call drop.2nd February 2011 at 04:09 #44536Zulfiquar AhmedGuest
Question: All Rf condition ok and no alram on the site then rscp bad how can i improve the rscp and what parameter i will checked
Answer: Hi below is the checklist
1) Antenna obstruction
2) Mechanical and electrical tilt
3) Check for CPICH power.
4) Check for VSWR Threshold.
5) Once again check for Alarms
This should solve the issue.
And finally we say RF condition is good only when the level and quality of signal is good.